Alarm Tone, Setup Menu TAB | Humminbird 981 manual

98x_Manual_531376-1_A.qxd 2/23/2005 11:41 AM Page 80

ALARM TONE

Alarm Tone selects the pitch of the alarm sound. A brief tone will be produced as you adjust the Alarm Tone so that you can select the tone that you can hear best.

To change the Alarm Tone setting:

1.Highlight Alarm Tone on the Alarms main menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Alarm Tone setting. (High, Medium, Low, Default = Medium)

SETUP MENU TAB

From any view, press the MENU key twice to access the tabbed Main Menu System, then press the RIGHT cursor key until the Setup tab is selected.

NOTE: Menu choices will vary depending on system settings such as whether the unit is set for Advanced User mode and what accessories are attached to the unit.

Setup Menu

Page 80

Image 80

Humminbird 981 manual Setup Menu TAB, To change the Alarm Tone setting, Highlight Alarm Tone on the Alarms main menu

Contents

98xManual531376-1A.qxd 2/23/2005 1139 AM Thank You Table of Contents Menu System Start-Up Options Menu Sonar X-Press MenuSide Imaging X-Press Menu Sonar Menu Tab Alarms Menu Tab Setup Menu Tab Views Menu Tab Accessories Menu Tab Troubleshooting Contact Humminbird Series Introduction HOW the 900 Series WorksSide Imaging Sonar Dualbeam Plus Sonar MULTI-MEDIA Card MMC/SD Slot Multi-Media Card MMC/SD Slot Accessory Bus Accessory BUSInstallation Overview Control Head Installation 900 Series has a wide variety of configurations Gimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Speed Communications Transducer Cable Collector Insert IN-DASH Mounting the Control Head Parts and tools specific to In-dash mounting areIn-dash mounting foam pads In-dash mounting template 23/2005 Connecting the Control Head Power Cable to the Boat Beginning of this procedure Motor Position Transducer InstallationTransom Transducer Trolling Motor Transducer Transom Transducer Installation Stepped Hull Without deadrise adjustment Not a hull, motor, or other transducer, etc Completely tighten Be fully tightened until all adjustments are madeHeaded pin can be inserted from either side of the bracket Force is necessary to pivot the assembly Normal Cavitation Trolling Motor Transducer Installation Test and Finish the Transducer Installation Hand-tighten only Follow these steps to stem mount the GPS receiver To the cable as shown Access Under Mounting Location Access Under Mounting LocationNo Access Under Mounting Location Speed Accessory Installation Finish Routing the Cable and Check GPS Receiver Operation Install the Speed accessory Hand tighten only Testing the System Installation Rotating Retaining Axial Clip to Remove Paddlewheel Powering UP the Control Head Getting Started Using Your 900 Series WHAT’S on the Sonar Display Triplog Sonar Bottom Presentation Understanding Sonar HistoryReal Time Sonar RTS Window KHz provides maximum coverage with 180 total beam width KHz provides highest resolution with 160 total beam widthUnderstanding Side Imaging WHAT’S on the Side Imaging Display Topography Changes Bottom Return Triplog Side Imaging Representation Side Imaging Technology HOW IT WorksSide Imaging on the Water Interpretation Submerged Ravine with Timber Submerged Standing and Fallen Timber, Plus Bait Fish Submerged Swimming Pool POWER/LIGHT KEY KEY FunctionsView KEY Menu KEY View Preset Keys WAY Cursor Control KEYExit KEY Info KEY Views MARK/GOTO KEYViews available on your 900 Series are Sonar views Sonar View Views and ReadoutsSonar View Sonar Zoom View Sonar Zoom View Split Sonar View Side Imaging ViewSplit Sonar View Side Imaging View SIDE/SONAR Combo View Side/Sonar Combo View Chart/Bird’s Eye Combo View Bird’s Eye View Chart View with Active Cursor Chart/Sonar View CHART/SIDE Combo View Chart/Side Combo View Chart View with Cursor Present Navigation WAYPOINTS, Routes and Tracks Waypoints, Routes and Tracks Navigate to a Waypoint or Position ADD a Waypoint Target or Trolling Grid Chart View with TargetChart View with Grid SAVE, Edit or Delete a Route Menu System Press Menu Sonar Tab, Normal Mode Sonar Tab, Advanced Mode START-UP Options MenuNormal Simulator System Status Start-Up Options Menu Self Test Accessory Test GPS Diagnostic View Normal OperationSimulator System Status GPS Diagnostic View Accessory TestAccessory Test Screen To Adjust Split Screen Position Sonar X-PRESS MenuActive Side Split Position To adjust the Sensitivity To adjust the Upper RangeSensitivity Upper Range Zoom Level Chart SpeedLower Range Sonar Colors Bottom LockBottom Range Side Imaging X-Press Menu Highlight Split Position on the Side Imaging X-Press MenuSide Imaging Views only SI Range SI SideSI Sensitivity SI Colors Navigation X-PRESS MenuTo change the SI Colors Highlight SI Colors on the Side Imaging X-Pressmenu Save Current Track Clear Current TrackTo Save Current Track To Clear Current Track Cancel Navigation Save Current RouteSkip Next Waypoint Remove Target Remove Grid Sonar Menu TABTo Remove a Grid Only if a Grid is active Fish ID+ Beam SelectSide View Frequency To change the Fish ID Sensitivity setting Fish ID SensitivityTo turn Fish ID+ on or off Highlight Fish ID Sensitivity on the Sonar main menu To change the RTS Window setting To adjust the Bottom ViewBottom View Zoom Width KHZ Sensitivity Depth LinesSurface Clutter Noise Filter Color BAR MAX DepthWater Type Temperature Graph To change the display of the Temperature GraphSonar View only, with Temperature input Navigation Menu TAB Routes TracksWaypoints Chart Orientation North ReferenceTrolling Grid Rotation Trackpoint Interval Track MIN Distance MAP DatumExport ALL NAV Data Delete ALL NAV Data Chart Menu TAB Chart Detail LevelTo change the Chart Detail Level setting MAP Borders LAT/LON Grid Spot SoundingsShaded Depth SET Simulation Position Alarms Menu TAB To change the Map Offset settingSET MAP Offset Clear MAP Offset Depth Alarm Fish ID AlarmLOW Battery Alarm Temp Alarm Drift Alarm OFF Course AlarmArrival Alarm Alarm Tone Setup Menu TABTo change the Alarm Tone setting Highlight Alarm Tone on the Alarms main menu Units Depth Units TempUnits Distance Units Speed User Mode Triplog ResetRestore Defaults Language Default Sonar View Select Readouts To change the Depth Offset setting To change the Temp Offset settingDepth Offset Temp Offset Speed Calibration Local Time ZoneDaylight Saving Time Position Format Nmea Output Time FormatDate Format Views Menu TAB To turn Sonar on or offFollowing views are available To Change the View Status of Any View Accessories Menu TAB TroubleshootingSeries Doesn’t Power Up Series Defaults to Simulator with a Transducer Attached Display Problems Control head loses power at high speeds Finding the Cause of Noise Other electronic devicesNoise re-appears Boat’s engine Year Limited Warranty Humminbird Service Policy For IN-WARRANTY service, complete the following steps Returning Your Unit for ServiceSeries Accessories Specifications Area of Coverage Appendix a Transducer Mounting Template XHS-9-SI-160-T Contact Humminbird