Speed Accessory Installation

98x_Manual_531376-1_A.qxd 2/23/2005 11:39 AM Page 26

FINISH ROUTING THE CABLE AND CHECK

GPS RECEIVER OPERATION

After installing a GPS receiver, you should perform the following procedure to finish routing the GPS cable to the control head and to check to make sure that the control head is working correctly.

1.Secure the cable along its path to the control head as needed with cable ties.

2.Plug in the GPS receiver cable into the Communications port on the control head. See Testing the System Installation to use the System Status start-up option and/or the GPS Diagnostic View to confirm a good installation.

1 2 3 4

1Power

2	Speed
3	Communications
4	Transducer	5
5	Cable Collector Insert	5
5	Cable Collector Insert

NOTE: You will only need to perform this procedure if you have a Speed-Only Sensor.

				7
1	Escutcheon Plate	6	5	Wedge
2	Wood Screw and Washer		6	Paddlewheel
3	Cable Clamp		7	Speed Accessory

4Axial Clip

Page 26

Image 26

Humminbird 981 manual Finish Routing the Cable and Check GPS Receiver Operation, Speed Accessory Installation

Contents

98xManual531376-1A.qxd 2/23/2005 1139 AM Thank You Table of Contents Side Imaging X-Press Menu Menu System Start-Up Options MenuSonar X-Press Menu Sonar Menu Tab Alarms Menu Tab Setup Menu Tab Views Menu Tab Accessories Menu Tab Troubleshooting Contact Humminbird Side Imaging Sonar Series IntroductionHOW the 900 Series Works Dualbeam Plus Sonar MULTI-MEDIA Card MMC/SD Slot Multi-Media Card MMC/SD Slot Accessory Bus Accessory BUSInstallation Overview Control Head Installation 900 Series has a wide variety of configurations Gimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Speed Communications Transducer Cable Collector Insert In-dash mounting foam pads IN-DASH Mounting the Control HeadParts and tools specific to In-dash mounting are In-dash mounting template 23/2005 Connecting the Control Head Power Cable to the Boat Beginning of this procedure Motor Position Transducer InstallationTransom Transducer Trolling Motor Transducer Transom Transducer Installation Stepped Hull Without deadrise adjustment Not a hull, motor, or other transducer, etc Completely tighten Be fully tightened until all adjustments are madeHeaded pin can be inserted from either side of the bracket Force is necessary to pivot the assembly Normal Cavitation Trolling Motor Transducer Installation Test and Finish the Transducer Installation Hand-tighten only Follow these steps to stem mount the GPS receiver To the cable as shown Access Under Mounting Location Access Under Mounting LocationNo Access Under Mounting Location Speed Accessory Installation Finish Routing the Cable and Check GPS Receiver Operation Install the Speed accessory Hand tighten only Testing the System Installation Rotating Retaining Axial Clip to Remove Paddlewheel Powering UP the Control Head Getting Started Using Your 900 Series WHAT’S on the Sonar Display Triplog Sonar Bottom Presentation Understanding Sonar HistoryReal Time Sonar RTS Window KHz provides maximum coverage with 180 total beam width KHz provides highest resolution with 160 total beam widthUnderstanding Side Imaging WHAT’S on the Side Imaging Display Topography Changes Bottom Return Triplog Side Imaging Representation Side Imaging Technology HOW IT WorksSide Imaging on the Water Interpretation Submerged Ravine with Timber Submerged Standing and Fallen Timber, Plus Bait Fish Submerged Swimming Pool View KEY POWER/LIGHT KEYKEY Functions Menu KEY Exit KEY View Preset KeysWAY Cursor Control KEY Info KEY Views available on your 900 Series are ViewsMARK/GOTO KEY Sonar views Sonar View Views and ReadoutsSonar View Sonar Zoom View Sonar Zoom View Split Sonar View Split Sonar ViewSide Imaging View Side Imaging View SIDE/SONAR Combo View Side/Sonar Combo View Chart/Bird’s Eye Combo View Bird’s Eye View Chart View with Active Cursor Chart/Sonar View CHART/SIDE Combo View Chart/Side Combo View Chart View with Cursor Present Navigation WAYPOINTS, Routes and Tracks Waypoints, Routes and Tracks Navigate to a Waypoint or Position ADD a Waypoint Target or Trolling Grid Chart View with TargetChart View with Grid SAVE, Edit or Delete a Route Menu System Press Menu Normal Simulator System Status Sonar Tab, Normal Mode Sonar Tab, Advanced ModeSTART-UP Options Menu Start-Up Options Menu Simulator Self Test Accessory Test GPS Diagnostic ViewNormal Operation System Status GPS Diagnostic View Accessory TestAccessory Test Screen Active Side To Adjust Split Screen PositionSonar X-PRESS Menu Split Position Sensitivity To adjust the SensitivityTo adjust the Upper Range Upper Range Zoom Level Chart SpeedLower Range Sonar Colors Bottom LockBottom Range Side Imaging X-Press Menu Highlight Split Position on the Side Imaging X-Press MenuSide Imaging Views only SI Range SI SideSI Sensitivity To change the SI Colors SI ColorsNavigation X-PRESS Menu Highlight SI Colors on the Side Imaging X-Pressmenu To Save Current Track Save Current TrackClear Current Track To Clear Current Track Skip Next Waypoint Cancel NavigationSave Current Route Remove Target To Remove a Grid Remove GridSonar Menu TAB Only if a Grid is active Fish ID+ Beam SelectSide View Frequency To turn Fish ID+ on or off To change the Fish ID Sensitivity settingFish ID Sensitivity Highlight Fish ID Sensitivity on the Sonar main menu Bottom View To change the RTS Window settingTo adjust the Bottom View Zoom Width Surface Clutter KHZ SensitivityDepth Lines Noise Filter Color BAR MAX DepthWater Type Sonar View only, with Temperature input Temperature GraphTo change the display of the Temperature Graph Navigation Menu TAB Routes TracksWaypoints Trolling Grid Rotation Chart OrientationNorth Reference Trackpoint Interval Export ALL NAV Data Track MIN DistanceMAP Datum Delete ALL NAV Data To change the Chart Detail Level setting Chart Menu TABChart Detail Level MAP Borders Shaded Depth LAT/LON GridSpot Soundings SET Simulation Position SET MAP Offset Alarms Menu TABTo change the Map Offset setting Clear MAP Offset LOW Battery Alarm Depth AlarmFish ID Alarm Temp Alarm Drift Alarm OFF Course AlarmArrival Alarm To change the Alarm Tone setting Alarm ToneSetup Menu TAB Highlight Alarm Tone on the Alarms main menu Units Distance Units DepthUnits Temp Units Speed Restore Defaults User ModeTriplog Reset Language Default Sonar View Select Readouts Depth Offset To change the Depth Offset settingTo change the Temp Offset setting Temp Offset Daylight Saving Time Speed CalibrationLocal Time Zone Position Format Nmea Output Time FormatDate Format Following views are available Views Menu TABTo turn Sonar on or off To Change the View Status of Any View Series Doesn’t Power Up Accessories Menu TABTroubleshooting Series Defaults to Simulator with a Transducer Attached Display Problems Control head loses power at high speeds Noise re-appears Finding the Cause of NoiseOther electronic devices Boat’s engine Year Limited Warranty Humminbird Service Policy For IN-WARRANTY service, complete the following steps Returning Your Unit for ServiceSeries Accessories Specifications Area of Coverage Appendix a Transducer Mounting Template XHS-9-SI-160-T Contact Humminbird