Temperature of 40 | Temperature Setting of 45 |
Means LED is OFF | Means LED is On |
2.To change the setting to 45°F (7°C) (blinking light ON) touch and release the wet switch contacts once more. Wait two seconds and then confirm that the temperature reading on the Control Head has changed to 45°F (7°C). Single touches will toggle the setting between 40°F (4°C) and 45°F (7°C).
NOTE: When the LED is set to ON it will flash every four seconds when the RSS is in operation (i.e. when the wet switch is submerged). Even when the LED is set to ON, the LED will not flash unless the wet switch is activated. If you want to test the RSS to make sure the LED is set to ON before using the RSS, wet your finger and hold it on the wet switch; if the LED is set to ON, the LED will begin to flash.
NOTE: Repeat steps 1 and 2 to turn off the LED when finished with night fishing.
Your SmartCast® is designed to provide years of trouble- free operation with virtually no maintenance. Follow these simple procedures to ensure your SmartCast® continues to deliver top performance.
WARNING! Never leave the RF35 SmartCast® product in a closed car or trunk - the extremely high temperatures generated in hot weather can damage the electronics.
Wrist Mounted Display Maintenance: If the Wrist Mounted Display comes into contact with salt spray, wipe the affected surfaces with a cloth dampened with fresh water. When cleaning the protective lens on the display, use a chamois and non-abrasive, mild cleaner. Do not wipe while dirt or grease is on the lens. Be careful to avoid scratching the lens. Do not use a chemical glass cleaner on the lens, as this may cause it to crack.
RSS™ Maintenance: After using the RSS™ in salt water, wipe the affected surfaces with a cloth dampened with fresh water. The RSS™ Wet Switch™ pins must be rinsed with fresh water after exposure to salt water to prevent corrosion.
If your RSS™ remains out of the water for a long period of time, it may take some time to wet it when returned to the water. Small air bubbles can cling to the surface of the RSS™ and interfere with proper operation. Wipe the face of the RSS™ with a wet cloth to remove them.
Check the battery position and make sure that the |
battery door is properly closed. Also, make sure that |
you have removed the plastic strip that is in the |
battery compartment when it is new. |
If this doesn’t help, replace the battery. After |
replacing the battery, if the unit still doesn’t power |
up, remove the battery door again and re-install. |
3. When in very shallow water, I get gaps in the |
bottom reading and inconsistent digital depth |
indication. |
The SmartCast® will work reliably in water 2 feet (0.6 |
meter) or deeper. The depth is measured from the |
RSS™. |
4. The display begins to fade out. Images are not as |
sharp as normal. |
Check the battery position and make sure that the |
battery door is properly closed. Also, make sure that |
you have removed the plastic strip that is located in |
the battery compartment when it is new. |
If this doesn’t help, replace the battery. After |
replacing the battery, if the unit still has a faded |
display, remove the battery door again and re-install. |
HUMMINBIRD® BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE PRODUCTS.
International Purchases
A separate warranty is provided by international distributors for units purchased outside the United States. This warranty is included by your local distributor and this distributor maintains local service for your unit. Warranties are only valid in the area of intended distribution. Units purchased in the United States or Canada must be returned to our factory in the United States for service.
Humminbird® Service Policy
Even though you'll probably never need to take advantage of our incredible service policy, it's good to know that we back our products this confidently. We do it because you deserve the best. We will make every effort to repair your unit within three business days from the receipt of your unit at our factory. This does not include shipping time to and from our factory. Units received on Friday are typically shipped by the following Wednesday, units received Monday are typically shipped by Thursday, etc.
All repair work is performed by factory-trained technicians
Wrist Mounted Display Specifications:
Power Requirement | ................................One 2450 CR Battery |
Display Matrix | 48 X 32 Pixels |
Display Type | STN |
RSSTM Specifications:
Power Requirement | One non-replaceable |
| Lithium RSSTM Battery |
Battery Expected Life | 3 years |
(approximately 500 hours of in-water use) |
Depth Capability | 2 - 120 feet (0.6 - 35 meters) |
Sonar Coverage | 90° @-10 dB* |
Sonar Operating Frequency | 125 kHz |
Operational Radio Frequency | 916.5 mHz |
| (433.92 mHz International) |
Operational Range | 75 feet (22 meters) |
* Area of bottom coverage equals twice the current depth.
3.Once you have made your selection you can either wait 20 seconds for programming mode to time out (the Start-Up screen will appear on the Control Head display), or continue immediately to the next procedure to change the channel.
Changing the Channel on the
Advanced RSS
To change the channel type on the Advanced RSS:
1.From the Light programming mode (see Turning on the Advanced RSS Blinking Light), touch and release the wet switch contacts twice more with your moist finger to change from the Light programming mode to the Channel programming mode. The temperature reading on the Control Head will change to show a temperature reading of 50°F (9°C) (channel set to A).
Temperature of 50 Means Channel | Temperature of 55 Means Channel |
is Set to A | is Set to B |
2.To change the setting to 55°F (12°C) (channel set to B) touch and release the wet switch contacts once more. Wait two seconds and then confirm that the temperature reading on the Control Head has changed to 55°F (12°C). Single touches will toggle the setting between 50°F (9°C) and 55°F (12°C).
3.Once you have made your selection, wait 20 seconds for programming mode to time out (the Start-Up screen will appear on the Control Head).
4.Use the SetUp Channel Select menu on the Control Head to switch the software to match the new channel designation on the Advanced RSS. See Channel Select (SetUp Menu) for more information.
CAUTION: Make sure that you change the Channel Selection on the Control Head to match the new Advanced RSS Channel before using the Advanced RSS.
Using a First Generation RSS
First generation RSS units still sold with other SmartCast® products come in two versions, Channel A and Channel B (RF40A and RF40B), and are both compatible with the RF35.
NOTE: When using either an RF40A or RF40B RSS with the RF35, you will not get water temperature, and you will not be able to turn on the LED or change the channel on the RSS. You will still be able to read digital depth and bottom contour information.
NOTE: When using an RF40A or RF40B RSS, make sure to select the matching channel from the CHANNEL SELECT menu on the Control Head.
If sonar performance becomes weak (i.e., there are bottom gaps or "0" depth readings) the bottom of the RSS™ needs to be cleaned with a drop or two of a 5 to 10 percent solution of liquid dish- washing detergent and water. Use approximately one tablespoon (15 ml) detergent to 8 ounces (237 ml) of water to remove oils from the face of the RSS™, then wipe with a damp cloth.
Troubleshooting
Do not attempt to repair the RF35 Wrist Mounted Display or RSS™ yourself. There are no user serviceable parts inside, and special tools and techniques are required for assembly to ensure the waterproof integrity of the housings. Repairs should be performed only by authorized Humminbird® technicians.
Many requests for repair received by Humminbird® involve units that do not actually need repair. These units are returned “no problem found.” If you have a problem with your SmartCast®, use the following troubleshooting guide before calling the Customer Resource Center or sending your unit in for repair.
1. The SmartCast® loses signal.
If the SmartCast® is not able to get an RF signal from the RSS™, the display will stop updating (the screen will freeze) and the RF35 SmartCast® screen will be displayed after several seconds. Whenever reception is lost or the
RSS™ emerges from the water for more than a few seconds, the RF35 SmartCast® screen will be displayed until the RSS™ is placed back in the water and reception is regained.
•The SmartCast® system is a line-of-sight wireless product. If objects are placed between the RSS™ and the Wrist Mounted Display, the reception may be lost.
•The RF35 depth range is 2 to 120 feet (0.6 to 35 meters). Erratic readings may occur in water that is shallower than 2 feet (0.6 m). In addition, because of the nature of sonar, this product is not intended for use in swimming pools or small enclosed bodies of water.
•Reeling the RSS™ too fast can cause loss of signal and the screen will freeze.
•Check the buoyant balance between the RSS™ and your tackle; over 0.2 ounce (5.7 grams) will submerge the RSS™, causing signal loss.
•The RF35 may not obtain its maximum RF distance of 75 feet (22 meters) unless the water is smooth. Waves or chop may reduce the RF range significantly.
NOTE: Retrieving the RSS™ too rapidly, or the repetitive rocking motion of rough water, can result in loss or distortion of the bottom detail on the display. For best bottom detail, perform a smooth and slow reel-in with constant speed and the rod tip up (holding the rod tip low or using a heavy line may cause the RSS™ to submerge and momentarily lose radio contact). The RSS™ has a maximum transmit range of 75 feet (22 meters). If the unit is cast or drifts more than 75 feet (22 meters) away from the receiver, the signal may be inconsistent or lost.
5. The display shows many black dots at high |
sensitivity settings. |
You are seeing noise or interference caused by one |
of several sources. Noise can be caused by other |
electronic devices. Turn off any nearby electronics |
and see if the problem goes away. Other sonar |
devices or any electronic device operating in the 900 |
mHz range (in the 400 mHz range for International |
versions) could cause interference with your |
SmartCast®. |
6. The display shows fluctuating depth readings and |
excessive clutter, including vertical bars that may |
be drawn on top of fish icons. |
The SmartCast® system comes with the capability to |
receive separate signals from a Channel A RSS™ or |
a Channel B RSS™. Two A- or B-type RSS™ units |
used simultaneously, as well as one A- and one B- |
type RSS™ unit used simultaneously, can cause RF |
interference between each other. |
7. The display jumps and the bottom has an abrupt |
change; sometimes a vertical line is missing or |
a black line from top to bottom is displayed. |
This display image jump is due to an automatic |
change in depth. New returns graphed at a different |
scale will not match up with the historic data already |
graphed at a higher or lower scale. Vertical lines can |
also occur as the radio signal from the RSS™ is lost |
and then regained in rough water conditions. |
Humminbird® 6 Month Limited Warranty
We warrant the original retail purchaser that products made by Humminbird® have been manufactured free from defects in materials and workmanship. This warranty is effective for 6 months from the date of original retail purchase. Humminbird® products found to be defective and covered by this warranty will be replaced or repaired free of charge at Humminbird® option and returned to the customer freight prepaid. Humminbird® sole responsibility under this warranty is limited to the repair or replacement of a product that has been deemed defective by Humminbird®. Humminbird® is not responsible for charges connected with the removal of such product or reinstallation of replaced or repaired parts.
This warranty does not apply to a product that has been:
•Improperly installed;
•Used in an installation other than that recommended in the product installation and operation instructions;
•Damaged or has failed because of an accident or abnormal operation;
•Repaired or modified by entities other than Humminbird®.
Please retain your original receipt as a proof of the purchase date. This will be required for in-warranty service.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES, OBLIGATIONS OR LIABILITIES ON THE PART OF HUMMINBIRD® AND WILL BE THE CUSTOMER'S EXCLUSIVE REMEDY, EXCEPT FOR ANY APPLICABLE IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE
to meet exacting factory specifications. Factory-serviced units go through the same rigorous testing and quality control inspections as new production units.
After the original warranty period, a standard flat rate service charge will be assessed for each repair (physical damage and missing parts are not included). Any repairs made after the original warranty will be warranted for an additional 90 days after service has been performed by our factory technicians. You can contact our Customer Resource Center or visit our website to verify the flat rate repair fee for your product (visit the Product Support section):
http://www.humminbird.com
We reserve the right to deem any product unserviceable when replacement parts are no longer available or impossible to obtain. This Service Policy is valid in the United States only. This applies only to Humminbird® products returned to our factory in Eufaula, Alabama. This Service Policy is subject to change without notice.
Returning Your Unit for Service
Before sending your unit in for repair, please contact the factory, either by phone or by email, to obtain a Repair Authorization Number for your unit. Please have your product model name and serial number available before calling the factory. If you contact the factory by e-mail, please include your product model name and serial number in the e-mail, and use Request for Repair Authorization Number for your e-mail subject header. You should include your Repair Authorization Number in all subsequent communications about your unit.
For IN-WARRANTY service, complete the following steps:
•Obtain a Repair Authorization Number from the Humminbird® Customer Resource Center.
•Tag product with your customer name, street address, phone number and your assigned Repair Authorization Number.
•Include a brief written description of the problem.
•Include a copy of your receipt (to show proof and date of purchase).
•Return product freight prepaid to Humminbird®, using an insured carrier with delivery confirmation.
For OUT-OF-WARRANTY service, complete the following steps:
•Obtain a Repair Authorization Number from the Humminbird® Customer Resource Center.
•Include payment in the form of credit card number and expiration date, money order or personal check. Please do not send cash.
•Tag product with your customer name, street address, phone number and your assigned Repair Authorization Number.
•Include a brief written description of the problem.
•Return product freight prepaid to Humminbird®, using an insured carrier with delivery confirmation.
FCC ID: ICLSMC1
Humminbird®
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference and;
(2)This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by Humminbird® could void the user’s authority to operate the device.
Contact Humminbird®
Your Humminbird® accessory is designed for trouble-free operation and is backed by a six-month warranty.
If you have any questions, contact our
Humminbird® Customer Resource Center:
By Telephone
(Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time):
1-800-633-1468
By e-mail
(typically we respond to your e-mail within three business days):
custserv@johnsonoutdoors.com
For direct shipping, our address is:
Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
