Manuals / Hunter Fan / Kitchen Appliance / Ventilation Hood

Hunter Fan 90054, 90058, 90052 manual No Existing Fan, Existing Construction - accessible from above

Models: 90054 90053 90052 90058

1 40

Page 11

Existing Construction – accessible from above

C11	EXISTING FAN

NO EXISTING FAN

Remove an existing fan and check to make sure the	Use the motor housing as a template to mark position.
opening is large enough to accommodate the new
motor housing (8”x 8.5”).

			”
8		5
8	.
”	8
	8

Cut out an opening for the housing.

C13

	5/8	5/8
		1/2
	1/2

C12

Slide the mounting rails into brackets.

C14

Position the correct depth mark at the bottom edge of the

joist based on the thickness of your sheetrock.

41718-01 3/29/2006

41718_EngS_3.29.06.indd 11

Mark position of screws by using holes as a template.

3/29/06 10:40:21 PM

Page 11

Image 11

Hunter Fan 90054, 90058 No Existing Fan, Existing Construction - accessible from above, Cut out an opening for the housing

Contents

G u i d e READ and SAVE THESE INSTRUCTIONS90052/90053/90054/90058 Saturn Bath Ventilator with Light I n s t a l l a t i o nW a r n i n g PREVENTATIVE MAINTENANCEMAINTENANCE POWER SUPPLY AND LOCK OUT SERVICE PANEL BEFORE SERVICING UNITNOTE Remove all packing materials before installation Before InstallationCheck all the parts. If damaged, call 1-888-830-1326 for replacements Estimated assembly time 30 to 60 minutesRemove the wiring cover Remove the motor/blower from the housingRemove the wiring cover screw with the side of the housingNew Construction - attaching to joist Choose Installation OptionFor New Construction - attaching to joist go to step A11, page Connect wires as shown A160Pull wires through the strain relief Reinstall the motor by inserting the tabs and pushing up Go to stepon page 17 to attach grille Connect wiring from the motor to the wiring cover plate1/8” Bit New Construction - suspended between joistsMark position of screws by using holes as a template Slide the mounting rails into bracketsTighten screws Connect wires as shownInstall the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover platebetween the motor and the housing Connect wiring from the motor to the wiring cover plateReinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinchedCut out an opening for the housing Existing Construction - accessible from aboveNO EXISTING FAN EXISTING FANDrill a hole in the center of each outline C15C16Pull wires through the strain relief 1/8” BitConnect wiring from the motor to the wiring cover plate Connect wires as shownInstall the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover platebetween the motor and the housing ON OFFReinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinchedMove the housing into position above the ceiling Existing Construction - accessible only from belowPull wires through strain relief Attach existing ducting to duct connector. Tape jointsthe wiring cover plate Connect wires as shownInstall the wiring cover plate. Make sure all wiring Connect wiring from the motor to the wiring cover plateON OFF Attaching the GrilleTurn on the power source Connect wiring harnessAlign glass dome and push up Install 2 Max 60 watt A-15 bulbs Not IncludedSlide light mount over posts Attach thumbscrewsSolution Trouble ShootingSolution SolutionWarranty 41718Span3.29.06.indd G u í ai n s t a l a c i ó n EspañolMantenimiento preventivo A D V E R T E N C I APRECAUCIÓN ADVERTENCIA95029-01-000 Antes de la instalaciónVerifique todos los 95044-01-000Retire las puntas de tornillo precargadas hasta que Retire el motor/soplador del alojamientoRetire las cubiertas de las puntas de tornillo precargadas Retire el tornillo de la cubierta del cableadoConstrucción nueva - fijación a la viga Escoja la opción de instalaciónOption A160Tire de los alambres por el aliviador de tensiones Conecte los alambres como se muestraAPAGADO Vaya al pasoen la página 37 para fijar la rejilla ENCENDIDOFije los rieles con los tornillos Construcción nueva - suspendido entre vigasDeslice los rieles de montaje en los soportes 1/8 de pulgNegro Apriete los tornillosConecte los alambres como se muestra NegroAPAGADO Vaya al pasoen la página 37 para fijar la rejilla ENCENDIDORecorte una abertura para el alojamiento C11 VENTILADOR EXISTENTESIN VENTILADOR EXISTENTE Construcción existente - accesible desde arribaFije los rieles en los tornillos C15C16broca de 1/8 de pulg Taladre un agujero en el centro de cada perfilOption Apriete los tornillosConecte los alambres como se muestra Conecte el cableado del motor a la placa de cubierta del cableadoen la página 37 para fijar la rejilla C25 C26ENCENDIDO APAGADO Vaya al pasoInstale los tornillos precargados en la viga o el marco D11 VENTILADOR EXISTENTEConstrucción existente - accesible sólo desde abajo Tire de los alambres por el aliviador de tensionesConecte los alambres como se muestra ENCENDIDO APAGADO Fijación de la rejillaVaya al paso en la página 37 para fijar la rejillaAlinee el domo de vidrio y levante Deslice el soporte sobre los postesInstale los tornillos de mano Instale 2 bombillas A-15 de 60 vatios como máximo No incluidasSolución Solución de problemasSolución Solución2500 Frisco Avenue, Memphis, Tennessee Impreso en China Garantía