Manuals / Hunter Fan / Kitchen Appliance / Ventilation Hood

Hunter Fan 90052, 90058, 90053, 90054 manual Tighten screws, Connect wires as shown

Models: 90054 90053 90052 90058

1 40

Page 9

				B18
	B17			B18

Tighten screws.

Pull wires through the strain relief.

B19				Ground
		Black		Green
	2 Pin			A	Bare Copper
		White			Bare Copper
		White
Fan Motor				Black	Main Switch 1 (AC In)
		White			White
Light	3 Pin	Black	Light
Light		Black	Light
		*Option
*Option Fan & Main Light Together				Black	Switch 2 (AC In)
*Option Fan & Main Light Together

Connect wires as shown.

B20

G	F

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under the

wiring cover plate.

41718-01 3/29/2006

41718_EngS_3.29.06.indd 9

B21 Install the wiring cover plate. Make sure all wiring connections are inside the box or under the Manual background

Connect 4” duct and vent to the outside. Tape joints. If ducting does not fit securely, an adapter may need to be purchased.

3/29/06 10:40:15 PM

Page 9

Image 9

Hunter Fan 90052, 90058, 90053 Tighten screws, Connect wires as shown, Install the wiring cover plate. Make sure all wiring

Contents

90052/90053/90054/90058 Saturn Bath Ventilator with Light READ and SAVE THESE INSTRUCTIONSI n s t a l l a t i o n G u i d eMAINTENANCE PREVENTATIVE MAINTENANCEPOWER SUPPLY AND LOCK OUT SERVICE PANEL BEFORE SERVICING UNIT W a r n i n gCheck all the parts. If damaged, call 1-888-830-1326 for replacements Before InstallationEstimated assembly time 30 to 60 minutes NOTE Remove all packing materials before installationRemove the wiring cover screw Remove the motor/blower from the housingwith the side of the housing Remove the wiring coverChoose Installation Option For New Construction - attaching to joist go to step A11, pageNew Construction - attaching to joist A160 Pull wires through the strain reliefConnect wires as shown on page 17 to attach grille Go to stepConnect wiring from the motor to the wiring cover plate Reinstall the motor by inserting the tabs and pushing upMark position of screws by using holes as a template New Construction - suspended between joistsSlide the mounting rails into brackets 1/8” BitInstall the wiring cover plate. Make sure all wiring Connect wires as shownconnections are inside the box or under the wiring cover plate Tighten screwsReinstall the motor by inserting the tabs and pushing up Connect wiring from the motor to the wiring cover plateinto position. Make sure the wires are not pinched between the motor and the housingNO EXISTING FAN Existing Construction - accessible from aboveEXISTING FAN Cut out an opening for the housingPull wires through the strain relief C15C161/8” Bit Drill a hole in the center of each outlineInstall the wiring cover plate. Make sure all wiring Connect wires as shownconnections are inside the box or under the wiring cover plate Connect wiring from the motor to the wiring cover plateReinstall the motor by inserting the tabs and pushing up ON OFFinto position. Make sure the wires are not pinched between the motor and the housingPull wires through strain relief Existing Construction - accessible only from belowAttach existing ducting to duct connector. Tape joints Move the housing into position above the ceilingInstall the wiring cover plate. Make sure all wiring Connect wires as shownConnect wiring from the motor to the wiring cover plate the wiring cover plateTurn on the power source Attaching the GrilleConnect wiring harness ON OFFSlide light mount over posts Install 2 Max 60 watt A-15 bulbs Not IncludedAttach thumbscrews Align glass dome and push upSolution Trouble ShootingSolution SolutionWarranty i n s t a l a c i ó n G u í aEspañol 41718Span3.29.06.inddPRECAUCIÓN A D V E R T E N C I AADVERTENCIA Mantenimiento preventivoVerifique todos los Antes de la instalación95044-01-000 95029-01-000Retire las cubiertas de las puntas de tornillo precargadas Retire el motor/soplador del alojamientoRetire el tornillo de la cubierta del cableado Retire las puntas de tornillo precargadas hasta queConstrucción nueva - fijación a la viga Escoja la opción de instalaciónTire de los alambres por el aliviador de tensiones A160Conecte los alambres como se muestra Optionen la página 37 para fijar la rejilla Vaya al pasoENCENDIDO APAGADODeslice los rieles de montaje en los soportes Construcción nueva - suspendido entre vigas1/8 de pulg Fije los rieles con los tornillosConecte los alambres como se muestra Apriete los tornillosNegro Negroen la página 37 para fijar la rejilla Vaya al pasoENCENDIDO APAGADOSIN VENTILADOR EXISTENTE C11 VENTILADOR EXISTENTEConstrucción existente - accesible desde arriba Recorte una abertura para el alojamientobroca de 1/8 de pulg C15C16Taladre un agujero en el centro de cada perfil Fije los rieles en los tornillosConecte los alambres como se muestra Apriete los tornillosConecte el cableado del motor a la placa de cubierta del cableado OptionENCENDIDO APAGADO C25 C26Vaya al paso en la página 37 para fijar la rejillaConstrucción existente - accesible sólo desde abajo D11 VENTILADOR EXISTENTETire de los alambres por el aliviador de tensiones Instale los tornillos precargados en la viga o el marcoConecte los alambres como se muestra Vaya al paso Fijación de la rejillaen la página 37 para fijar la rejilla ENCENDIDO APAGADOInstale los tornillos de mano Deslice el soporte sobre los postesInstale 2 bombillas A-15 de 60 vatios como máximo No incluidas Alinee el domo de vidrio y levanteSolución Solución de problemasSolución Solución2500 Frisco Avenue, Memphis, Tennessee Impreso en China Garantía