Manuals / Hunter Fan / Kitchen Appliance / Ventilation Hood

Hunter Fan 90053 manual Go to step, on page 17 to attach grille, between the motor and the housing

Models: 90054 90053 90052 90058

1 40

Download 40 pages 7.47 Kb

Page 10

Image 10

Test the motor. If the motor does not run,

B22

H Manual background

Connect wiring from the motor to the wiring cover plate.

B23

Reinstall the motor by inserting the tabs and pushing up

into position. Make sure the wires are not pinched

between the motor and the housing.

B24	B25
	I

Secure the motor by tightening the 2 screws.

Turn on the power source.

B26

B27

Go to step

OFF

Test the motor. If the motor does not run,

check the plug connection.

on page 17 to attach grille.

41718-01 3/29/2006

41718_EngS_3.29.06.indd 10

3/29/06 10:40:18 PM

Page 10

Image 10

Hunter Fan 90053, 90058 Go to step, on page 17 to attach grille, Connect wiring from the motor to the wiring cover plate

Contents

I n s t a l l a t i o n READ and SAVE THESE INSTRUCTIONS90052/90053/90054/90058 Saturn Bath Ventilator with Light G u i d ePOWER SUPPLY AND LOCK OUT SERVICE PANEL BEFORE SERVICING UNIT PREVENTATIVE MAINTENANCEMAINTENANCE W a r n i n gEstimated assembly time 30 to 60 minutes Before InstallationCheck all the parts. If damaged, call 1-888-830-1326 for replacements NOTE Remove all packing materials before installationwith the side of the housing Remove the motor/blower from the housingRemove the wiring cover screw Remove the wiring coverFor New Construction - attaching to joist go to step A11, page Choose Installation OptionNew Construction - attaching to joist Pull wires through the strain relief A160Connect wires as shown Connect wiring from the motor to the wiring cover plate Go to stepon page 17 to attach grille Reinstall the motor by inserting the tabs and pushing upSlide the mounting rails into brackets New Construction - suspended between joistsMark position of screws by using holes as a template 1/8” Bitconnections are inside the box or under the wiring cover plate Connect wires as shownInstall the wiring cover plate. Make sure all wiring Tighten screwsinto position. Make sure the wires are not pinched Connect wiring from the motor to the wiring cover plateReinstall the motor by inserting the tabs and pushing up between the motor and the housingEXISTING FAN Existing Construction - accessible from aboveNO EXISTING FAN Cut out an opening for the housing1/8” Bit C15C16Pull wires through the strain relief Drill a hole in the center of each outlineconnections are inside the box or under the wiring cover plate Connect wires as shownInstall the wiring cover plate. Make sure all wiring Connect wiring from the motor to the wiring cover plateinto position. Make sure the wires are not pinched ON OFFReinstall the motor by inserting the tabs and pushing up between the motor and the housingAttach existing ducting to duct connector. Tape joints Existing Construction - accessible only from belowPull wires through strain relief Move the housing into position above the ceilingConnect wiring from the motor to the wiring cover plate Connect wires as shownInstall the wiring cover plate. Make sure all wiring the wiring cover plateConnect wiring harness Attaching the GrilleTurn on the power source ON OFFAttach thumbscrews Install 2 Max 60 watt A-15 bulbs Not IncludedSlide light mount over posts Align glass dome and push upSolution Trouble ShootingSolution SolutionWarranty Español G u í ai n s t a l a c i ó n 41718Span3.29.06.inddADVERTENCIA A D V E R T E N C I APRECAUCIÓN Mantenimiento preventivo95044-01-000 Antes de la instalaciónVerifique todos los 95029-01-000Retire el tornillo de la cubierta del cableado Retire el motor/soplador del alojamientoRetire las cubiertas de las puntas de tornillo precargadas Retire las puntas de tornillo precargadas hasta queEscoja la opción de instalación Construcción nueva - fijación a la vigaConecte los alambres como se muestra A160Tire de los alambres por el aliviador de tensiones OptionENCENDIDO Vaya al pasoen la página 37 para fijar la rejilla APAGADO1/8 de pulg Construcción nueva - suspendido entre vigasDeslice los rieles de montaje en los soportes Fije los rieles con los tornillosNegro Apriete los tornillosConecte los alambres como se muestra NegroENCENDIDO Vaya al pasoen la página 37 para fijar la rejilla APAGADOConstrucción existente - accesible desde arriba C11 VENTILADOR EXISTENTESIN VENTILADOR EXISTENTE Recorte una abertura para el alojamientoTaladre un agujero en el centro de cada perfil C15C16broca de 1/8 de pulg Fije los rieles en los tornillosConecte el cableado del motor a la placa de cubierta del cableado Apriete los tornillosConecte los alambres como se muestra OptionVaya al paso C25 C26ENCENDIDO APAGADO en la página 37 para fijar la rejillaTire de los alambres por el aliviador de tensiones D11 VENTILADOR EXISTENTEConstrucción existente - accesible sólo desde abajo Instale los tornillos precargados en la viga o el marcoConecte los alambres como se muestra en la página 37 para fijar la rejilla Fijación de la rejillaVaya al paso ENCENDIDO APAGADOInstale 2 bombillas A-15 de 60 vatios como máximo No incluidas Deslice el soporte sobre los postesInstale los tornillos de mano Alinee el domo de vidrio y levanteSolución Solución de problemasSolución SoluciónGarantía 2500 Frisco Avenue, Memphis, Tennessee Impreso en China