Manuals / Hunter Fan / Kitchen Appliance / Ventilation Hood

Hunter Fan 90058 New Construction - suspended between joists, 1/8” Bit, 41718EngS3.29.06.indd

Models: 90054 90053 90052 90058

1 40

Download 40 pages 7.47 Kb

Page 8

Image 8

New Construction – suspended between joists

B11

Slide the mounting rails into brackets.

B12

	5/8	5/8
		1/2
	1/2

Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock.

B13

B14

E	1/8” Bit

Mark position of screws by using holes as a template.

Drill a hole in the center of each outline.

B15

Insert screws, leaving space between the screw head and the joist. Screws are not provided.

41718_EngS_3.29.06.indd 8

B16

Attach the rails onto the screws.

41718-01 3/29/2006

3/29/06 10:40:12 PM

Page 8

Image 8

Hunter Fan 90058, 90052 manual New Construction - suspended between joists, Slide the mounting rails into brackets, 1/8” Bit

Contents

READ and SAVE THESE INSTRUCTIONS 90052/90053/90054/90058 Saturn Bath Ventilator with LightI n s t a l l a t i o n G u i d ePREVENTATIVE MAINTENANCE MAINTENANCEPOWER SUPPLY AND LOCK OUT SERVICE PANEL BEFORE SERVICING UNIT W a r n i n gBefore Installation Check all the parts. If damaged, call 1-888-830-1326 for replacementsEstimated assembly time 30 to 60 minutes NOTE Remove all packing materials before installationRemove the motor/blower from the housing Remove the wiring cover screwwith the side of the housing Remove the wiring coverNew Construction - attaching to joist Choose Installation OptionFor New Construction - attaching to joist go to step A11, page Connect wires as shown A160Pull wires through the strain relief Go to step on page 17 to attach grilleConnect wiring from the motor to the wiring cover plate Reinstall the motor by inserting the tabs and pushing upNew Construction - suspended between joists Mark position of screws by using holes as a templateSlide the mounting rails into brackets 1/8” BitConnect wires as shown Install the wiring cover plate. Make sure all wiringconnections are inside the box or under the wiring cover plate Tighten screwsConnect wiring from the motor to the wiring cover plate Reinstall the motor by inserting the tabs and pushing upinto position. Make sure the wires are not pinched between the motor and the housingExisting Construction - accessible from above NO EXISTING FANEXISTING FAN Cut out an opening for the housingC15C16 Pull wires through the strain relief1/8” Bit Drill a hole in the center of each outlineConnect wires as shown Install the wiring cover plate. Make sure all wiringconnections are inside the box or under the wiring cover plate Connect wiring from the motor to the wiring cover plateON OFF Reinstall the motor by inserting the tabs and pushing upinto position. Make sure the wires are not pinched between the motor and the housingExisting Construction - accessible only from below Pull wires through strain reliefAttach existing ducting to duct connector. Tape joints Move the housing into position above the ceilingConnect wires as shown Install the wiring cover plate. Make sure all wiringConnect wiring from the motor to the wiring cover plate the wiring cover plateAttaching the Grille Turn on the power sourceConnect wiring harness ON OFFInstall 2 Max 60 watt A-15 bulbs Not Included Slide light mount over postsAttach thumbscrews Align glass dome and push upTrouble Shooting SolutionSolution SolutionWarranty G u í a i n s t a l a c i ó nEspañol 41718Span3.29.06.inddA D V E R T E N C I A PRECAUCIÓNADVERTENCIA Mantenimiento preventivoAntes de la instalación Verifique todos los95044-01-000 95029-01-000Retire el motor/soplador del alojamiento Retire las cubiertas de las puntas de tornillo precargadasRetire el tornillo de la cubierta del cableado Retire las puntas de tornillo precargadas hasta queEscoja la opción de instalación Construcción nueva - fijación a la vigaA160 Tire de los alambres por el aliviador de tensionesConecte los alambres como se muestra OptionVaya al paso en la página 37 para fijar la rejillaENCENDIDO APAGADOConstrucción nueva - suspendido entre vigas Deslice los rieles de montaje en los soportes1/8 de pulg Fije los rieles con los tornillosApriete los tornillos Conecte los alambres como se muestraNegro NegroVaya al paso en la página 37 para fijar la rejillaENCENDIDO APAGADOC11 VENTILADOR EXISTENTE SIN VENTILADOR EXISTENTEConstrucción existente - accesible desde arriba Recorte una abertura para el alojamientoC15C16 broca de 1/8 de pulgTaladre un agujero en el centro de cada perfil Fije los rieles en los tornillosApriete los tornillos Conecte los alambres como se muestraConecte el cableado del motor a la placa de cubierta del cableado OptionC25 C26 ENCENDIDO APAGADOVaya al paso en la página 37 para fijar la rejillaD11 VENTILADOR EXISTENTE Construcción existente - accesible sólo desde abajoTire de los alambres por el aliviador de tensiones Instale los tornillos precargados en la viga o el marcoConecte los alambres como se muestra Fijación de la rejilla Vaya al pasoen la página 37 para fijar la rejilla ENCENDIDO APAGADODeslice el soporte sobre los postes Instale los tornillos de manoInstale 2 bombillas A-15 de 60 vatios como máximo No incluidas Alinee el domo de vidrio y levanteSolución de problemas SoluciónSolución SoluciónGarantía 2500 Frisco Avenue, Memphis, Tennessee Impreso en China