Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 13 manual Restoring from service position, Take care not to get your hand trapped

Models: 13 11, 13, 11 Bio, 13 Bio

1 52

Download 52 pages 31.33 Kb

Page 37

Image 37

MAINTENANCE RIDER 11 BIO/13 BIO

WARNING!

Take care not to get your hand trapped.

8.Lift off the drive belt (1). Then pull out the pin (2).

9. Pull the frame forwards and refit the pin.

10.Grasp the front edge of the cutting unit, pull out and raise into the service position.

If the cylindrical bolt, which is now holding the cutting unit is removed, the cutting unit can be lifted off.

Restoring from service position

To leave the service position, reverse the procedures set out in ”Placing in the service position”. Make sure that the cutting unit’s ”lug” enters the loop correctly on the underside of the machine, see diagram.

6017-225

6017-226

6017-227

8009-123

English – 35

Page 37

Image 37

Husqvarna Restoring from service position, Take care not to get your hand trapped, MAINTENANCE RIDER 11 BIO/13 BIO

Contents

Operator´s manual Rider 11 Rider 13 Rider 11 Bio Rider 13 BioEnglish Svenska Rider 11 Bio and Rider 13 Bio CONTENTS Operator’s Manual for Rider 11 and RiderIMPORTANT INFORMATION Dear customer INTRODUKTIONTravel and transport on public roads TowingGood service SAFETY INSTRUCTIONSSerial number EXPLANATION OF SYMBOLS General use Safety instructionsRead the operator’s manual before starting the machine Clear the area of objects before mowingPersonlig skyddsutrustning Keep children away from the area to be mowedSAFETY INSTRUCTIONS Make sure that you have first aid equipmentDriving on slopes Be especially careful when driving on slopesProceed as follows Mow upwards and downwards on slopes, not sidewaysChildren MaintenanceNever allow children to operate the machine Never fill the fuel tank indoorsThe engine and the exhaust system become very hot during operation Do not smoke when carrying out maintenanceRisk of burn injuries if touched SAFETY INSTRUCTIONSNever run the machine in an enclosed area Transportmachine SAFETY INSTRUCTIONSPresentation PRESENTATIONLocation of the controls Throttle and Choke lever PRESENTATION RIDER 11 / 11 BIOClutch pedal Brake pedal / Parking brakeSpeed limiter PRESENTATION RIDER 13/13 BIOParking brake Throttle and Choke leverLift lever for cutting unit Cutting unitRider 11 Bio and Rider 13 Bio have a twin-blade BioClip cutting unit Lifting of the cutting unit transport positionsee safety instructions Lever for adjustment of cutting heightSeat FuellingDRIVING the lever when you select neutral. If youBefore starting Starting the engineWarm engine Cold engineDRIVING 5. Set the throttle control midway between position 1 and2. For Rider 13 and Rider 13 Bio Driving the machineFor Rider 11 and Rider 11 Bio The clutch must be used for each gear changeMowing pattern Cutting tipsDRIVING IMPORTANT INFORMATIONStopping the engine Hill start, manual gearboxRelease lever Rider 13 and Rider 13 Bio DRIVINGMaintenance schedule MAINTENANCEMaintenance interval MaintenanceEngine hood Dismantling of the machine hoodsFront hood Rider 11 and Rider MAINTENANCELeft-hand fender Right-hand fenderMAINTENANCE EnglishMAINTENANCE Checking and adjustment of the steering wiresCheck and adjust the brakes on Rider 13 and Rider 13 Bio Adjusting the brake Rider 11 and Rider 11 BioPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 BioReplacement of the fuel filter Checking and adjustment of the throttle wireMAINTENANCE Replacing the air filter Do not use compressed air to clean the paper filterMAINTENANCE IMPORTANT INFORMATIONProcedures on contact with acid Check the level of the battery acidIgnition system Checking of the fuel pump’s air filterRider Rider Inspecting the safety systemMAINTENANCE Check the engine’s cooling air intake Checking the tyre pressureMAINTENANCE IMPORTANT INFORMATIONMAINTENANCE Checking the cutting unit’s parallelism32 - English MAINTENANCE6008-026H 8009-138Service position for BioClip MAINTENANCE RIDER 11 BIO/13 BIOPlacing in service position 5. Disengage the spring from the drive belt tensioning wheel MAINTENANCE RIDER 11 BIO/13 BIOTake care not to get your hand trapped Restoring from service positionMAINTENANCE RIDER 11 BIO/13 BIO Replacing the break-pin BioClip Checking the bladesKlippaggregat bakutkast BioClipCheck the engine’s oil level LUBRICATIONChanging the oil IMPORTANT INFORMATIONLubrication of belt tensioner Check the transmission’s oil level Rider 13 and Rider 13 BioGeneral lubrication LUBRICATIONLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 BioCheck that the lock-ring is correctly positioned in the slot LUBRICATIONProblem TROUBLE SHOOTING SCHEDULEProcedure STORAGE ServiceWinter storage Dimensions TECHNICAL DATAEngine Electrical systemRider 13 Bio Rider 11 BioTECHNICAL DATA DimensionsEU declaration of conformity Only applies to Europe EU-DECLARATION OF CONFORMITYPre-delivery service SERVICEJOURNAL RIDER 11/13After first 5 hours Work doneWork done SERVICEJOURNALDate, mileage, stamp, sign 46 - EnglishWork done SERVICEJOURNALDate, mileage, stamp, sign SERVICEJOURNAL ´+H$r¶6C¨Work done Date, mileage, stamp, signPage 114 00 ´+H$r¶6C¨ 2002W07