Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 11, 13, 11 Bio, 13 Bio Checking the tyre pressure, Maintenance, Important Information

Models: 13 11, 13, 11 Bio, 13 Bio

1 52

Download 52 pages 31.33 Kb

Page 32

Image 32

MAINTENANCE

Checking the tyre pressure

The tyre pressure should be 60 kPa (0.6 kp/cm2) all round.

To improve driving the pressure on the rear tyres can be reduced to 40 kPa (0.4 kp/cm2).

The maximum tyre pressure is 100 kPa (1.0 kp/cm2).

IMPORTANT INFORMATION

Different tyre pressures on the front tyres will result in the blades cutting the grass at different heights.

Check the engine’s cooling air intake

Raise the engine cover.

Check that the cooling intake is free from leaves, grass and dirt.

If the cooling intake is blocked this will interfere with the cooling of the engine, which can damage the engine.

6008-030

6008-006

30 – English

Page 32

Image 32

Husqvarna 11, 13, 11 Bio, 13 Bio manual Checking the tyre pressure, Check the engine’s cooling air intake, Maintenance

Contents

English Rider 11 Rider 13 Rider 11 Bio Rider 13 BioOperator´s manual Svenska IMPORTANT INFORMATION CONTENTS Operator’s Manual for Rider 11 and RiderRider 11 Bio and Rider 13 Bio INTRODUKTION Dear customerTravel and transport on public roads TowingSerial number SAFETY INSTRUCTIONSGood service EXPLANATION OF SYMBOLS Safety instructions General useRead the operator’s manual before starting the machine Clear the area of objects before mowingKeep children away from the area to be mowed Personlig skyddsutrustningSAFETY INSTRUCTIONS Make sure that you have first aid equipmentBe especially careful when driving on slopes Driving on slopesProceed as follows Mow upwards and downwards on slopes, not sidewaysMaintenance ChildrenNever allow children to operate the machine Never fill the fuel tank indoorsDo not smoke when carrying out maintenance The engine and the exhaust system become very hot during operationRisk of burn injuries if touched SAFETY INSTRUCTIONSTransport Never run the machine in an enclosed areamachine SAFETY INSTRUCTIONSLocation of the controls PRESENTATIONPresentation PRESENTATION RIDER 11 / 11 BIO Throttle and Choke leverClutch pedal Brake pedal / Parking brakePRESENTATION RIDER 13/13 BIO Speed limiterParking brake Throttle and Choke leverCutting unit Lift lever for cutting unitRider 11 Bio and Rider 13 Bio have a twin-blade BioClip cutting unit Lifting of the cutting unit transport positionLever for adjustment of cutting height see safety instructionsSeat Fuellingthe lever when you select neutral. If you DRIVINGBefore starting Starting the engineCold engine Warm engineDRIVING 5. Set the throttle control midway between position 1 andDriving the machine 2. For Rider 13 and Rider 13 BioFor Rider 11 and Rider 11 Bio The clutch must be used for each gear changeCutting tips Mowing patternDRIVING IMPORTANT INFORMATIONHill start, manual gearbox Stopping the engineRelease lever Rider 13 and Rider 13 Bio DRIVINGMAINTENANCE Maintenance scheduleMaintenance interval MaintenanceDismantling of the machine hoods Engine hoodFront hood Rider 11 and Rider MAINTENANCERight-hand fender Left-hand fenderMAINTENANCE EnglishChecking and adjustment of the steering wires MAINTENANCEAdjusting the brake Rider 11 and Rider 11 Bio Check and adjust the brakes on Rider 13 and Rider 13 BioPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 BioMAINTENANCE Checking and adjustment of the throttle wireReplacement of the fuel filter Do not use compressed air to clean the paper filter Replacing the air filterMAINTENANCE IMPORTANT INFORMATIONCheck the level of the battery acid Procedures on contact with acidIgnition system Checking of the fuel pump’s air filterMAINTENANCE Inspecting the safety systemRider Rider Checking the tyre pressure Check the engine’s cooling air intakeMAINTENANCE IMPORTANT INFORMATIONChecking the cutting unit’s parallelism MAINTENANCEMAINTENANCE 32 - English6008-026H 8009-138Placing in service position MAINTENANCE RIDER 11 BIO/13 BIOService position for BioClip MAINTENANCE RIDER 11 BIO/13 BIO 5. Disengage the spring from the drive belt tensioning wheelMAINTENANCE RIDER 11 BIO/13 BIO Restoring from service positionTake care not to get your hand trapped Checking the blades Replacing the break-pin BioClipKlippaggregat bakutkast BioClipLUBRICATION Check the engine’s oil levelChanging the oil IMPORTANT INFORMATIONCheck the transmission’s oil level Rider 13 and Rider 13 Bio Lubrication of belt tensionerGeneral lubrication LUBRICATIONLubrication Rider 11 and Rider 11 Bio Lubrication of front wheel bearingsCheck that the lock-ring is correctly positioned in the slot LUBRICATIONProcedure TROUBLE SHOOTING SCHEDULEProblem Winter storage ServiceSTORAGE TECHNICAL DATA DimensionsEngine Electrical systemRider 11 Bio Rider 13 BioTECHNICAL DATA DimensionsEU-DECLARATION OF CONFORMITY EU declaration of conformity Only applies to EuropeSERVICEJOURNAL RIDER 11/13 Pre-delivery serviceAfter first 5 hours Work doneSERVICEJOURNAL Work doneDate, mileage, stamp, sign 46 - EnglishDate, mileage, stamp, sign SERVICEJOURNALWork done ´+H$r¶6C¨ SERVICEJOURNALWork done Date, mileage, stamp, signPage ´+H$r¶6C¨ 2002W07 114 00