GETTING STARTED WITH
HUSQVARNA’S ROBOTIC LAWNMOWER
1PLACEMENT OF AND CONNECTING THE CHARGING STATION21.See chapter 3.2 in the Operator’s Manual.Place the charging station at a central position in theworking area, with a lot of open space in front of the
charging station and on a relatively horizontal surface.
2. Connect the transformer’s low voltage cable to the |
|
charging station and the transformer. |
|
3. Connect the transformer to a 230 V wall socket. | 3 |
| |
| 1 |
CHARGING THE BATTERY AND PLACEMENT
OF THE BOUNDARY WIRE
See chapters 3.3 and 3.4 in the Operator’s Manual.
CONNECTING THE BOUNDARY WIRE
3 | See chapter 3.5 in the Operator’s Manual. | 1 | 2 | 3 | |
1. | Open the connectors and lay the wire ends in the recesses |
|
|
| |
| on each connector. |
|
|
| |
2. Press the connectors together using a pair of pliers. |
|
|
| ||
3. | Cut off any surplus boundary wire. Cut 1 to 2 cm above |
|
|
| |
|
| the connectors. |
|
|
|
| 4. | Press the connectors onto the contact pins, marked A, on |
|
| 4 |
|
| the charging station. It is important that the |
|
|
|
|
| wire is connected to the |
|
|
|
|
|
|
|
|
1. | Place the robotic lawnmower in the charging |
|
| station to charge the battery while the boundary |
|
2 wire is laid. Set the main switch to position 1. |
| |
2. Lay the boundary wire so that it forms a loop |
| |
| around the working area. |
|
3. | Make an eyelet at the point where the guide wire | 0 cm / 0" |
| will later be connected. See step 4.5. |
|
|
| 5 cm / 2" |
|
| 3 |
10 cm / 4"
30 cm / 12"
20 cm / 8"
4PLACEMENT OF AND CONNECTINGSee chapter 3.6 in the Operator’s Manual.THE GUIDE WIRE
1.Run the guide wire through the slot at the bottom of the charging station.
2.Fit the connector to the guide wire in the same way as for the boundary wire, according to the instructions above.
3.Fasten the connector to the contact pin marked Guide on the charging station.
4.Lay the guide wire at least 2 metres straight out from the front edge of the charging station.
5.Run the guide wire to the point on the boundary loop the connection will be made. Avoid laying the wire at tight angles.
6.Cut the boundary wire with a wire cutters at the centre of the eyelet that was made in step 2.3.
7.Connect the guide wire to the boundary wire using the accompanying couplers. Press the couplers completely together with a pair of pliers.
1
7
1
4
min 2 m / 7 ft
1.Main switch
2.STOP button
3.Charging strip
4.LED for function check of the boundary and guide wires
5.Cutting height indication
6.Display
7.Keypad
|
|
|
|
|
|
|
| 30 cm |
|
| 5 |
|
|
|
|
|
|
2 | 3 | 4 |
|
|
|
|
| 20 cm |
| 6 |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
1 |
| 7 |
|
|
|
|
| 5 cm |
|
| Charging station | Transformer | Low voltage cable | Boundary wire and | Staples | Connectors | Measurement |
|
|
|
|
| couplers |
|
| gauge |