MAINTENANCE
Maintenance schedule
The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section.
Maintenance | Daily |
| Weekly | Monthly | |
maintenance | maintenance | maintenance | |||
| |||||
|
|
|
|
| |
Clean the outside of the machine. |
| X |
|
| |
|
|
|
|
| |
Make sure the throttle trigger lock and the throttle function correctly |
| X |
|
| |
from a safety point of view. |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
Check that the stop switch works correctly. |
| X |
|
| |
|
|
|
|
| |
Check that the cutting attachment does not rotate at idle. |
| X |
|
| |
|
|
|
|
| |
Clean the air filter. Replace if necessary. |
| X |
|
| |
|
|
|
|
| |
Check that the guard is undamaged and not cracked. Replace the |
| X |
|
| |
guard if it has been exposed to impact or is cracked. |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
Check the blade for cracks and chips or damage. Replace if |
| X |
|
| |
necessary. |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
Check that the locking nut of the cutting equipment is tighten |
| X |
|
| |
correctly. (326Ex) |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
Check that the locking screw of the cutting equipment is tightened |
|
|
|
| |
correctly. (326ES) |
|
|
|
| |
|
|
|
|
| |
Check that nuts and screws are tight. |
| X |
|
| |
|
|
|
|
| |
Check that there are no fuel leaks from the engine, tank or fuel lines. |
| X |
|
| |
|
|
|
|
| |
Check the starter and starter cord. |
|
| X |
| |
|
|
|
|
| |
Check that the vibration damping elements are not damaged. |
|
| X |
| |
|
|
|
|
| |
Clean the outside of the spark plug. Remove it and check the |
|
|
|
| |
electrode gap. Adjust the gap to 0.5 mm (.20”), or replace the spark |
|
| X |
| |
plug. Check that the spark plug is fitted with a suppressor. |
|
|
|
| |
|
|
|
|
| |
Clean the machine’s cooling system. |
|
| X |
| |
|
|
|
|
| |
Clean or replace the spark arrestor screen on the muffler (only |
|
| X |
| |
applies to mufflers without a catalytic converter). |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
Clean the outside of the carburettor and the space around it. |
|
| X |
| |
|
|
|
|
| |
Check that the angle gear is filled |
|
| X |
| |
Fill if necessary using special grease. |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
The flexible drive shaft must be lubricated every 25 working hours |
|
| X |
| |
or more frequently. (326Ex) |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
Check the fuel filter from contamination and the fuel hose from |
|
|
| X | |
cracks or other defects. Replace if necessary. |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
Check all cables and connections. |
|
|
| X | |
|
|
|
|
| |
Check the clutch, clutch springs and the clutch drum for wear. |
|
|
| X | |
Replace if necessary by an autorized service workshop. |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
Replace the spark plug. Check that the spark plug is fitted with a |
|
|
| X | |
suppressor. |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
Check and clean the spark arrestor screen on the muffler (only |
|
|
| X | |
applies to mufflers fitted with a catalytic converter). |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
Check and if necessary, clean the exhaust port of cylinder from |
|
|
| X | |
carbon deposits. |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
26 – English |
