PARA REMOVER CORREA DE IMPULSIÓN
1.Remueva la cubierta de la impulsión y fijador de la correa.
2.Remueva la correa en la polea de la caja de engranajes.
3.Haga descansar la segadora en su lado con el filtro de aire y el carburador mirando hacia arriba.
4.Remueva la cuchilla y la polea del motor.
Cubierta de la impulsion
Polea de la caja de engranajes
Fijador de la correa
Correa
PARA CAMBIAR CORREA DE IMPULSIÓN
1.Colocar la nueva correa de mando en la polea del motor, adentro la retención de correa.
2.Colocar la otra extremidad de la nueva correa de mando a través del orificio en el bastidor.
3.Reinstale la cuchilla.
4.Vuelva la segadora a la posición vertical.
5.Instale la correa nueva en la polea de la caja de engranajes.
6.Reinstale la fijador de la correa y cubierta de la impulsión.
NOTA: Siempre use la correa aprobada por la fábrica para asegurarse que calce y dure.
PARA AJUSTAR EL MANGO
El mango puede ser montado a una posición alta o baja. Los agujeros de montaje en el mango inferior están fuera del centro para levantar y bajar el mango.
1.Remueva el mango superior y conexióne(s) el asegurar él (los) cable(s) al mango infe- rior.
2.Remueva las clavijas de horquilla de la clavija de montaje del puntal del mango.
3.Apreite el mango inferior hacia dentro para removerlo de las clavijas de montaje.
4.Gire el mango inferior por encima para levantar o bajar el mango.
5.Vuelva a montar las clavijas de horquilla por encima de las clavijas de montaje.
6.Vuelva a montar el mango superior y todas las partes removidas del mango inferior.
APRIETE
PARA AJUSTE
Mango inferior
Clavija de montaje
Puntal | Clavija de horquilla |
del mango | |
Posición | Posición |
para segar | para segar |
Clavija | Puntal |
de horquilla | del mango |
Clavija de |
|
montaje |
|
POSICIÓN BAJA | POSICIÓN ALTA |
Cartridge Slot
Back plate
Cover
IN-LINE FUEL FILTER
The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carbu- retor, replacement is required.
1.With engine cool, remove filter and plug fuel line sections.
2.Place new fuel filter in position in fuel line with arrow pointing towards carbu- retor.
3.Be sure there are no fuel line leaks and clamps are properly positioned.
4.Immediately wipe up any spilled gaso- line.
Clamp | Clamp |
Fuel
Filter
MUFFLER
Inspect and replace corroded muffler as it could create a fire hazard and/or damage.
SPARK PLUG
Replace spark plug at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFIC- ATIONS” section of this manual.
CLEANING
IMPORTANT: For best performance, keep mower housing free of
CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.
•Clean the underside of your lawn mower by scraping to remove
•Clean engine often to keep trash from accumulating. A clogged engine runs hotter and shortens engine life.
•Keep finished surfaces and wheels free of all gasoline, oil, etc.
•We do not recommend using a garden hose to clean lawn mower unless the electrical system, muffler, air filter and carburetor are covered to keep water out. Water in engine can result in short- ened engine life.
CLEAN UNDER DRIVE COVER
Clean under drive cover at least twice a sea- son. Scrape underside of cover with putty knife or similar tool to remove any
Adaptador de | Ranura | Chavetero del |
la cuchilla |
| ciguenal |
Arandela de |
|
|
seguridad |
|
|
Cuchilla |
|
|
SERVICE AND ADJUSTMENTS
WARNING: To avoid serious injury, before performing any service and adjustments:
1.Release control bar and stop engine.
2.Make sure the blade and all moving parts have completely stopped.
3.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.
Perno | Arandela |
|
de la | endurecida | Retención de correa |
cuchilla | Borde de salida |
Mango inferior
GIRAR
LAWN MOWER
TO ADJUST CUTTING HEIGHT
See “TO ADJUST CUTTING HEIGHT” in the Operation section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the rear wheels of your mower, is provided to minimize the possibility that objects will be thrown out of the rear of the mower into the operator mowing position. If the deflector becomes damaged, it should be replaced.
34 | 15 |