WARNING: When pulling starter rope, the rope can unexpectedly jerk back toward engine causing serious injury. To avoid this risk, carefully follow these instructions:

Move rocker switch to "I" position.

5.Grasp starter cord handle. Se Fig. 9

a.Pull rope out slowly until you feel drag.

b.Without allowing the rope to retract, continue pulling rope with one rapid full arm stroke.

c.Return rope slowly to original position.

Note:

Following the instructions listed in the steps above avoids potential damage to the recoil mechanism.

6.If engine fails to start after 3 attempts repeat steps 2 thru 5 and try again.

7.When engine starts:

a.Momentarily move choke lever to "1/2 CHOKE" position until engine runs smoothly.

b.Next, move choke lever to "NO CHOKE" position.

Note:

If engine starts but falters when choke in moved to "NO CHOKE" position:

a.Momentarily move choke lever to "FULL CHOKE" position.

b.Next, move choke lever to "NO CHOKE" until engine runs smoothly.

c.Finally, move control to "NO CHOKE" position.

If engine dies after choke is moved to "NO CHOKE" position, repeat steps 2 thru 7 to restart engine.

8.If engine fires but does not continue to run, move choke control lever to "NO CHOKE" position.

•Push yellow compression relief valve in.

•Pull starter rope again.

9.If engine fails to start after 3 attempts move choke control to "FULL CHOKE" position.

•Push yellow compression relief valve in.

•Pull starter rope again.

10.If engine does not start after following steps 1 thru 9, contact your Authorized Tecumseh Servicing Dealer. DO NOT attempt to start or troubleshoot this engine in any other way.

1.

Full Choke

 

 

2.

1/2 Choke

3

 

3. No Choke

2

1

 

 

 

Fig. 10 Choke Lever Position

After the engine is started and has run for a few seconds, move the choke lever as far as it will go in the opposite direction from the starting position.

Tilt the unit back onto the drag stake to raise the tines off the ground.

With the tines still off the ground, squeeze and release the throttle trigger a few times. If the tines do not stop rotating when trigger is released, adjust carburetor idle speed as instructed in Adjustment/Maintenance section.

To shut off the engine, release the throttle control lever and move the On/Off Switch to the “O” position.

OPERATING TECHNIQUE AND HANDY TIPS

1.Start engine and tilt unit back until tines are off the ground. Squeeze throttle lever to full speed position (lever tight against grip). Remember, this unit is equipped with a governed engine and must always be run at full speed position.

2.Lower front of unit until tines begin to dig into ground to start filling.

3.Unit will tend to walk forward at this point and must be firmly held back to allow tines to till.

4.If adjustments to tilling depth must be made, proceed as follows:

a. Shut engine off by moving switch to “O” position.

DRAG

STAKE

 

 

Fig. 11

 

 

b. Remove hairpin cotter and clevis pin from drag

Fig. 9 Starter Cord Handle Location

stake and adjust upward if unit is tilling too

deeply. Adjust stake downward if more depth is

 

 

 

 

necessary.

8

c. Move switch to “I” position and restart engine to

continue tilling.

Page 7 Page 9
Page 8
Image 8
Husqvarna 966957301 specifications Operating Technique and Handy Tips, Full Choke No Choke
Page 7 Page 9

966957301 specifications

The Husqvarna 966957301 is a versatile and powerful chainsaw that caters to both professional and avid outdoor enthusiasts. Celebrated for its robust design and advanced technology, this chainsaw has become a popular choice for cutting tasks ranging from tree felling to limbing and firewood cutting.

At the heart of the Husqvarna 966957301 is a highly efficient 50.2cc engine. This powerful engine provides a remarkable balance of performance and fuel efficiency, enabling users to complete tasks quickly without frequent refueling. The engine features an upgraded air injection system, which enhances air filtration and reduces wear on engine components, extending the life of the chainsaw.

One of the standout features of the Husqvarna 966957301 is its lightweight construction. Weighing in at just over 10 pounds, this chainsaw is designed for ease of use and maneuverability. This ensures that even during extended periods of operation, users experience less fatigue and can work comfortably.

The chainsaw incorporates Husqvarna’s signature X-Torq technology, which significantly lowers fuel consumption and emissions. X-Torq design allows for a cleaner burn, thereby contributing to environmental sustainability while still delivering the power needed for tough cutting tasks. This technology not only benefits users by saving on fuel costs but also aligns with modern environmental standards.

For enhanced safety, the Husqvarna 966957301 features an integrated chain brake, which quickly stops the chain in the event of kickback. The ergonomic handle with anti-vibration technology minimizes vibrations during operation, further improving comfort and reducing strain on the hands and arms.

Another notable characteristic is the Quick-release air filter, which makes maintenance and cleaning easier. With an easy-access location, users can efficiently change or clean the air filter without complicated disassembly. The tool-less chain tensioning mechanism allows for quick adjustments on the go, ensuring optimum cutting performance.

Lastly, the Husqvarna 966957301 is designed with durable materials, providing both longevity and reliability. Whether for professional logging or home landscaping, this chainsaw stands out for its innovative features, exceptional power, and ease of use, making it a valuable tool for any chainsaw enthusiast.
Top Page Image Contents