OPERATION
•The average lawn should be cut to approximately
•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.•
The average lawn should be cut to approximately
•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.
ATTACHEMENT
LIFT LEVER
|
|
|
| ATTACHMENT |
|
|
|
| HEIGHT |
6 | 3 | 2 | 1 | ADJUSTMENT |
|
|
| KNOB | |
|
|
|
|
FIG. 11
TO OPERATE MOWER (See Figs. 11 and 12)
Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.
•Select desired height of cut.
•Start mower blades by engaging attachment clutch control.
•TO STOP MOWER BLADES - disengage attachment clutch control.
CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the dis- charge guard in place.
ATTACHMENT CLUTCH LEVER “ENGAGED”
POSITION
ATTACHMENT CLUTCH LEVER “DISENGAGED” POSITION
FIG. 12
TO OPERATE ON HILLS
CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.
•Choose the slowest speed before starting up or down hills.
•Avoid stopping or changing speed on hills.
•If slowing is necessary, move throttle control lever to
slower position. | 10 |
•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.
•Move gearshift lever to 1st gear and be sure you have allowed room for tractor to roll slightly as you restart movement.
•To restart movement, slowly release parking brake and clutch/brake pedal.
•Make all turns slowly.
TO TRANSPORT
•Raise attachment lift to highest position with attach- ment lift control.
•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.
•Do not push or tow tractor at more than five (5) MPH.
NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL
•The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.
•Check engine oil with tractor on level ground. See engine manual for further instructions.
•For cold weather operation you should change oil for easier starting (See engine manual).
•To change engine oil, see the Customer Responsibili- ties section in this manual.
ADD GASOLINE
•Fill fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.
IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW 32°F(0° C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.
WARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before stor- age of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instruc- tions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.
CAUTION: Fill to bottom of gas tank filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.
