Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna LTH125 owner manual TO ADJUST MOTION CONTROL LEVER See, Transmission Removal/Replacement

Models: LTH125

1 52

Download 52 pages 50.57 Kb

Page 23

TO ADJUST MOTION CONTROL LEVER (See Fig.29)

SERVICE AND ADJUSTMENTS

TO ADJUST MOTION CONTROL LEVER (See Fig.29)

The motion control lever has been preset at the factory and adjustment should not be necessary.

If for any reason the motion control lever will not hold its position while at a selected speed, it may be adjusted at the friction pack located on the right side of transmission.

•Park tractor on level surface. Stop tractor by turning ignition key to “OFF” position, and engage parking brake.

•Adjust motion control lever by tightening adjustment locknut one half (1/2) turn.

NOTE: If for any reason the effort to move the motion control lever becomes too excessive, reverse the above adjustment procedure by loosening locknut 1/4 to 1/2 turn.

Road test tractor after adjustment and repeat procedure if necessary.

ADJUSTMENT

LOCKNUT

FIG. 29

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation before operating the tractor. See “Purge transmission” in Opera- tion section of this manual.

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 30)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 30

23

Image 23

Husqvarna LTH125 TO ADJUST MOTION CONTROL LEVER See, Transmission Removal/Replacement, To Adjust Steering Wheel Alignment

Contents

LTH125 I. GENERAL OPERATION SAFETY RULESIV. SERVICE Safe Operation Practices for Ride-On MowersCUSTOMER RESPONSIBILITIES PRODUCT SPECIFICATIONSCUSTOMER RESPONSIBILITIES TABLE OF CONTENTSSERVICE AND ADJUSTMENTS REPAIR PARTS - TRACTORCONTENTS OF HARDWARE PACK BEFORE ROLLING TRACTOR OFF SKID ASSEMBLYTOOLS REQUIRED FOR ASSEMBLY TO REMOVE TRACTOR FROM CARTONDo not smoke. Fumes from charged battery acid are explosive HOW TO SET UP YOUR TRACTORPREPARE BATTERY See Fig INSTALL SEAT See FigASSEMBLY INSTALL BATTERY See Figs. 4CHECKLIST INSTALL MULCHER PLATE See Figs.6TO CONVERT TO BAGGING OR DISCHARGING ASSEMBLYMOTION CONTROL LEVER Selects the speed and direction of tractor HEIGHT ADJUSTMENT KNOB - Used to adjust the mower heightOPERATION KNOW YOUR TRACTORSTOPPING See Fig HOW TO USE YOUR TRACTORTO ADJUST MOWER CUTTING HEIGHT See Fig TO SET PARKING BRAKE See FigTO TRANSPORT See Fig BEFORE STARTING THE ENGINETO OPERATE MOWER See Fig TO OPERATE ON HILLSPage OPERATION MOWING TIPSMULCHING MOWING TIPS BEFORE EACH USE LUBRICATION CHARTCUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONSBLADE CARE TRACTORBRAKE OPERATION TIRESTRANSAXLE PUMP FLUID BATTERY See FigV-BELTS TRANSAXLE COOLINGAIR FILTER See Fig CLEAN AIR SCREEN See FigENGINE LUBRICATIONSPARK PLUGS CLEANINGENGINE COOLING FINS See Fig MUFFLERTO REMOVE MOWER See Fig SERVICE AND ADJUSTMENTSTO INSTALL MOWER See Fig CAUTION BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTSSERVICE AND ADJUSTMENTS TO LEVEL MOWER HOUSINGSERVICE AND ADJUSTMENTS TO ADJUST BRAKE See FigTO REPLACE MOWER BLADE DRIVE BELT See Fig TO REPLACE MOTION DRIVE BELT See Fig.28FRONT WHEEL TOE-IN/CAMBER TO ADJUST MOTION CONTROL LEVER See Fig.29TRANSMISSION REMOVAL/REPLACEMENT TO ADJUST STEERING WHEEL ALIGNMENTTO REPLACE HEADLIGHT BULB TO START ENGINE WITH A WEAK BATTERY See FigTO REMOVE HOOD AND GRILL ASSEMBLY See Fig.32 TO REPLACE FUSEENGINE TO ADJUST THROTTLE CONTROL CABLE See Fig.33TO ADJUST CARBURETOR See Fig SERVICE AND ADJUSTMENTSFUEL SYSTEM BATTERYSTORAGE OTHERCORRECTION TROUBLESHOOTING POINTSPROBLEM CAUSEwhen turning engine TROUBLESHOOTING POINTSPROBLEM Battery will not chargeTRACTOR - MODEL NO. LTH125 HC125H42C, PRODUCT NO SCHEMATICELECTRICAL REPAIR PARTSTRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NO ELECTRICAL KEY PART DESCRIPTION NO. NOREPAIR PARTS TRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NOTRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NO CHASSIS AND ENCLOSURESREPAIR PARTS Plug Button PARTDESCRIPTION 532005479TRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NO DRIVEREPAIR PARTS PART REPAIR PARTSTRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NO DRIVETRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NO STEERING AND FRONT AXLEREPAIR PARTS PART REPAIR PARTSTRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NO STEERING AND FRONT AXLETRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NO. 954 ENGINEREPAIR PARTS PART REPAIR PARTSTRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NO ENGINEPART SEATREPAIR PARTS TRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NODECALS WHEELS AND TIRESREPAIR PARTS TRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NO. 954 00TRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NO LIFTREPAIR PARTS LIFT KEY PART NO. NO. DESCRIPTIONREPAIR PARTS TRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NOPage PART 42 MOWER DECKREPAIR PARTS TRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NO. 954TRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NO HYDRO-GEAR TRANSAXLE - MODEL NOREPAIR PARTS TRACTOR- -MODEL NO. LTH125 HC125H42C PRODUCT NO KEY PARTNO. NO REPAIR PARTSSERVICE NOTES SERVICE NOTES Page SECTION 1 LIMITED WARRANTY WARRANTY STATEMENTHUSQVARNA FOREST & GARDEN CO 9006-J PERIMETER WOODS DRIVE CHARLOTTE, NORTH CAROLINA532145999 Rev