WARNING: Make sure there are no bystanders close to the unit, especially in front of the machine, when the traction drive lever is engaged. When the traction drive lever is engaged the machine will immediately move forward.
WARNING: Attach the grass catcher prior to starting the engine to prevent injury. Do not operate the unit without the grass catcher.
IMPORTANT: Before mowing, check to make sure the cut- ting reel knives and bedknife are sharp and clearance between the reel and bedknife is properly adjusted. Do not operate the unit with the cutting reel engaged for a long period of time when not cutting grass - this can damage the reel and bedknife. Grass provides a natural lubrication of the reel knives and bedknife.
1.Always check area to be mowed and remove any debris, rocks or other foreign objects. Take special note of locations of hazards or potential objects that could damage the mower or cause potential safety issues.
2.Check mower over to make sure it is operating properly, the grass catcher is properly attached and all the guards and shields are properly installed.
3.Transport the mower to the collar of the green. Remove the transport wheel (if attached).
4.To begin mowing, the throttle should be set at a speed where the operator feels comfortable operating the unit. Transport the mower to the collar of the green and position it in the direction to be mowed. Engage the cutting reel drive lever, raise the cutting reel by pushing the handles down and engage the traction drive lever. Set the cutting reel down at the proper location to start mowing and mow in a straight line.
5.There are marks located on each side of the grass catcher to indicate the mowing width. Align one of the marks with the outside edge of the uncut grass and mow using the mark as a guide. Fig.
6.To stop mowing at the end of the green when approaching the collar, disengage the cutting reel drive lever, drive off the green and disengage the traction drive lever.
7.To turn the unit at the end of a row, when approaching the end of the row, push down on the handles to raise the cutting reel and turn the mower by pivoting it on the traction drum. When the turn has been completed, locate the last row mowed and position the mower straight with the last row. Set the cutting reel down at the proper location to begin mowing the next row.
8.When the grass catcher becomes full, stop the mower and turn off the engine. Remove the grass catcher and dispose of the grass clippings in an appropriate location. Treat the grass clippings as combustible waste, keeping it away from any possibility of a fire hazard.
Transporting
Transporting the Model 50, using the optional transport wheels, under its own power, requires considerable skill. Practice maneuvering in an open area before attempting to drive it from one location to another.
Marks |
Fig. |
WARNING: Make sure there are no bystanders close to the unit, especially in front of the machine, when the traction drive lever is engaged. When the traction drive lever is engaged the machine will immediately move forward.
WARNING: Do not drive the machine, without trans- port wheels, when it is on anything but turf if the transport wheels are not installed. The rear roller and the roller shaft may become damaged resulting in abnormal rotation.
1.Set the throttle to the “slow” position.
2.Grip the operator handle with one hand and engage the traction drive lever slowly.
3.As soon as the traction drive is engaged the machine will move forward. Grip the operator handles securely with both hands.
4.To stop the machine; disengage the traction drive lever then engage the brake.
Transporting the Model 50, on a vehicle, requires two or more people to load and unload the machine onto the transport vehicle.
WARNING: Make sure there are no bystanders close to the unit when loading or unloading to prevent injury.
WARNING: When loading or unloading onto a trans- port vehicle the engine must be shutoff. The unit must not be loaded or unloaded using it’s own power. It should be maneuvered manually.
WARNING: Do not attempt to grab the unit in the area near the cutting reel or bedknife when lifting the unit by hand. The reel and bedknife are very sharp and can cause injury.
WARNING: Take care that the machine does not fall from the loading ramp or off of the transport vehicle.
111132_0409 |
