Rear View - Plumbing Hook-Up
BRINE
LINE
DRAIN
LINE

Installation Instructions

1.Determine the best location for your water softener, bearing in mind the location of your water supply lines, drain line and 110 volt AC electrical outlet. Subjecting the softener to freezing or temperatures above 110°F (43°C) will void the warranty.

2.Water to supply outside faucets used to water lawns and gardens should not be softened. A new water line is often required to be connected to supply hard water to the inlet of the water softener and to the outside faucets. Cut the water line between where it enters the house; before any

lines that branch off to feed the hot water heater or other fixtures in the house; and as near the desired location of the water softener as possible. Install a tee fitting on the feed end of the cut pipe and an elbow fitting on the other end. Install piping from the tee to the inlet of the water

OUTLET

softener and from the elbow to the outlet to the softener.INLET To server the water lines which branch off to feed outside

faucets, cut the branch lines approximately two inches from the fitting on the main water line. Install an elbow on the end of the pipe nearest the outside faucet and a cap

on the end connected to the existing water line. Install piping from the tee on the inlet to the water softener to the elbow on the pipe to the outside faucet. Following this procedure will result in all lines in the house, with the exception of the outside faucets but including the water heater and therefore the hot water lines, being supplied with soft water.

3.Familiarize yourself with the location of the inlet, outlet and drain on the control valve. Be very careful not to get the controls wet.

4.Attach the bypass valve to the control valve. Connect the inlet and outlet of the water softener to the plumbing in the house. The control valve must not be subjected to temperatures above 71°C (160°F). To avoid damaging the control valve when sweat fittings are used, solder the threaded copper adapters to the copper pipe and then, using teflon tape, screw the assembly into the bypass valve.

CAUTION - do not use pipe thread compound as it may attack the material in the valve body.

5.Using teflon tape, screw the 1/2” hose barb into the drain port in the valve. Attach 1/2” drain hose to the hose barb and tighten securely with a hose clamp. Run the drain line to a floor drain or a laundry drain. Complete any necessary plumbing.

6.On the twin tank units, pull the 3/8” brine line through the hole in the side of the brine tank. Connect the brine line to the fitting on the side of the valve using the nut and ferrule. Tighten snugly.

2

Page 4
Image 4
HydroSurge 5600 operation manual Outlet

5600 specifications

The HydroSurge 5600 is a state-of-the-art water purification system designed to meet the demands of modern living while prioritizing efficiency and sustainability. This advanced device utilizes a combination of cutting-edge technologies to deliver unparalleled performance in water purification, making it an essential addition to homes and businesses alike.

One of the standout features of the HydroSurge 5600 is its multi-stage filtration system. It employs a combination of activated carbon, reverse osmosis, and UV sterilization to ensure that water is not only clean but also safe for consumption. The activated carbon filter effectively removes chlorine, sediment, and various contaminants that can affect the taste and quality of water. The reverse osmosis membrane further enhances purification by filtering out up to 99% of dissolved solids, heavy metals, and microorganisms. The UV sterilization technology then provides an added layer of protection by deactivating any remaining bacteria and viruses, guaranteeing that the water is free from harmful pathogens.

In addition to its impressive filtration capabilities, the HydroSurge 5600 is designed with user convenience in mind. It features a digital control panel that allows users to monitor the system's performance, filter life, and maintenance alerts, ensuring that the purification process remains efficient at all times. This user-friendly interface simplifies the operation and ensures even those who are not technologically inclined can easily utilize the system.

Energy efficiency is another key characteristic of the HydroSurge 5600. It is engineered to minimize water wastage, using only a fraction of the water compared to traditional filtration systems. This eco-friendly approach not only conserves resources but also reduces monthly utility bills, making it a cost-effective choice.

Moreover, the HydroSurge 5600 boasts a sleek and modern design that can seamlessly fit into any kitchen space or commercial environment. Its compact size ensures that it does not occupy too much counter space while maintaining a stylish appearance.

In summary, the HydroSurge 5600 represents the pinnacle of water purification technology. With its multi-stage filtration system, user-friendly interface, energy efficiency, and stylish design, it stands out as a reliable choice for ensuring clean and safe drinking water. Whether for home or business use, the HydroSurge 5600 promises to deliver top-notch performance and the peace of mind that comes with knowing you are consuming the highest quality water available.