44 iSeries and AS/400e System Builder
#2817 #2817 PCI 155 Mbps MMF ATM IOA
The #2817 is a 155 Mbps ATM PCI card that allows the server to be attached to an ATM network using the Multi- Mode
Fiber (MMF) 62.5 micron interface. This interface is intended for connection to both local area switches and direct
connection to service provider equipment. The #2817 is used typically where 155 Mbps speeds are required over distances
of less than 2 km. The #2817 is capable of supporting both multiple emulated LAN environments and enhanced TCP/IP
performance with OS/400 V5R1.
Technical specifications and industry standards supported are available at the ATM Forum Web site at:
http://www.atmforum.com
This card is a 64-bit card but is allowed to plug into any 32-bit or 64-bit slot.
Minimum operating system level: OS/400 V5R1
The #2817 is a Customer Install Feature.
#2849 #2849 10/100 Mbps Ethernet Adapter
The #2849 allows an iSeries server to attach to standardized 100 Mbps high-speed Ethernet LANs and allows attachment
to existing 10 Mbps Ethernet LANs. The adapter comes standard with an RJ45 connector for attachment to UTP-5 media.
Cabling for 10 Mbps must be CAT-3 or CAT-5, cabling for 100 Mbps must be CAT-5 that meets or exceeds Industry Standard
EIA/TIA T568A or T568B. Maximum cable length is 100 meters.
Supports LAN console.
The #2849 is not supported on any Integrated Netfinity Server/Integrated xSeries Server.
Minimum operating system level: OS/400 V5R2
The #2849 is a Customer Install Feature.
The #2849 was withdrawn from marketing on 01 June 2006. The #5700 PCI 1 Gbps Ethernet IOA is the recommended
replacement.
#4723 #4723 PCI 10 Mbps Ethernet Adapterr
The #4723 PCI 10 Mbps Ethernet Adapter provides single attachment to one Carrier Sense Multiple Access/Collision
Detect Local Area Network. The feature consists of an adapter card and internal code which supplies Ethernet version 2
and IEEE 802.3 MAC plus IEEE 802.2 LLC functions. The Ethernet/IEEE 802.3 IOA is capable of operating in half or full
duplex mode. The #4723 has an RJ45 connector and a 15-pin D-Shell connector for attachment to client-supplied cabling.
A vendor AUI Ethernet cable or RJ45 twisted pair cable must be ordered separately.
The #4723 is not supported by #2790 PCI Integrated Netfinity Server or #2791/#2799 PCI Integrated xSeries Server.
Minimum operating system level: OS/400 V4R5
The #4723 is a Customer Install Feature.
#4745 #4745 PCI 2-line WAN IOA
The #4745 supports up to two multiple protocol communications ports when one or two of the following cables are
attached:
#0348 V.24/EIA232 20-ft (6 m) PCI cable
#0349 V.24/EIA232 50-ft (15 m) PCI cable
#0353 V.35 20-ft PCI cable
#0354 V.35 50-ft PCI cable
#0355 V.35 80-ft PCI cable
#0356 V.36 20-ft PCI cable
#0358 V.36 150-ft PCI cable
#0359 X.21 20-ft PCI cable
#0360 X.21 50-ft PCI cable
#0365 V.24/EIA232 80-ft PCI cable
#0367 Operations Console PCI Cable
Multiple #0367s can be ordered (but only one allowed per #4745) to serve as consoles for secondary partitions when
logical partitioning (#0140) is specified. When the #4745 is selected to support ECS, one of the following cables must be
specified:
#0348 V.24/EIA232 20-ft (6 m) PCI cable (default)
#0349 V.24/EIA232 50-ft (15 m) PCI cable
#0365 V.24/EIA232 80-ft PCI cable
Minimum operating system level: OS/400 V4R5
The #4745 is a Customer Install Feature.
The #4745 was withdrawn from marketing on 01 June 2006.