SERIAL INTERFACE DEVELOPERS GUIDE
/* PC Master Command Code Enumerations */
enum
{
CMD_FPGA_UPDATE_AVAILABLE = 1,
CMD_COPY_SFLASH_PAGE, /* Copy a page of serial flash memory to DSP */
CMD_PROG_SFLASH_FULL, /* Program a full page to serial flash */
CMD_PROG_SFLASH_PARTIAL, /* Program a partial page to serial flash */
CMD_PROG_PRODUCT_ID, /* Program DSP Data flash with Product ID */
CMD_READ_PRODUCT_ID, /* Read Product ID from DSP Data flash */
CMD_PROG_STATIC_CFG, /* Program DSP Data flash with Static Config */
CMD_READ_STATIC_CFG, /* Read Static Config from DSP Data flash */
CMD_GET_CAMERA_TIME, /* Read the RTC time and store to scratch pad */
CMD_SET_CAMERA_TIME, /* Set the RTC time from scratch pad */
CMD_GET_NVM_DATA, /* Read NVM data block to scratch pad */
CMD_SET_NVM_DATA, /* Set NVM data block from scratch pad */
CMD_FOCUS_MOTOR_FAR, /* Call focus-out routine */
CMD_FOCUS_MOTOR_NEAR, /* Call focus-in routine */
CMD_IMAGE_GRAB, /* Grab image into utility memory (Buffer Supplied) */
CMD_READ_UTILITY_MEMORY, /* Read a block of utility memory (Address Supplied) */
CMD_NUC_FLASH_RAMP, /* Debug Command to write ramp to parameter blocks */
CMD_NUC_FLASH_MEMORY, /* Read a block of NUC flash memory (Address Supplied) */
CMD_NUC_FLASH_TEST_PATTERN, /* Debug Command to write test pattern to NUC blocks */
CMD_TEC_DRV_ENABLE, /* Enable/Disable TEC Drive */
CMD_TEC_TEMP_SELECT, /* Select TEC Temperature (High/Low) */
CMD_CAL_FLAG_SERVO, /* Call either the Open or Close Routine */
CMD_CAL_FLAG_REFERENCE, /* Call either the Heated or Ambient Routine */
CMD_ONE_PT_REFRESH, /* Perform a directed 1-point refresh calibration */
CMD_TWO_PT_NUC, /* Perform a directed 2-point calibration */
CMD_LOAD_COLOR_PAL, /* Load user selected color palette */
CMD_LOAD_OVLY_PAL, /* Load user selected overlay palette */
CMD_PIN_CHECK, /* Verify Memory Unlock PIN */
CMD_FAN_SPEED_OPERATION, /* Command to Test Fan Operation */
CMD_GET_ADC_VALUES, /* DEBUG ADC RETRIEVAL FUNCTION */
CMD_ENABLE_RETICLE, /* Turn Reticle on/off */
CMD_RETICLE_POSITION, /* Move Reticle to desired location */
CMD_ONE_PT_UPDATE, /* Perform a directed 1-point update calibration */
CMD_WRITE_VID_ENC_REG, /* DEBUG VIDEO ENCODER WRITE REGISTER */
CMD_PERFORM_TEST, /* Perform user supplied test */
CMD_OVERLAY_REFRESH, /* Refresh symbology overlay */
CMD_FREEZE_IMAGE, /* Freeze/Unfreeze Display Image */
CMD_DETECT_BAD_PIXELS, /* NO LONGER USED */
CMD_IRCON_LOAD_LUT, /* Custom LUT table creation for radiometrics */
CMD_LOAD_RAD_PARAMS, /* Load Rad Params for compile time software */
CMD_RESET_PFV_COUNT, /* Toggles PFV Frame count bit */
CMD_CLEAR_CONTINUE_FLAG, /* Clears the idle while fault continue flag */
CMD_UNIFORMITY_TEST, /* Command to initiate a uniformity (flat field noise) test*/
CMD_WRITE_UTILITY_MEMORY, /* Write a block of utility memory (Address Supplied) */
CMD_ADV_DETECT_BAD_PIXELS, /* Command to initiate flash update of advanced detection of
pixel defects */
CMD_UPLOAD_NUC, /* Command to intiate flash write of uploaded NUC terms */
CMD_DOWNLOAD_NUC, /* Command to intiate flash read of active NUC terms */
CMD_COMPILE_DEFECT_LISTS, /* Command to initiate a compilation of NUC defects to FLASH */
CMD_RESTORE_FACTORY_DEFECTS, /* Command to NUC to factory defect state */
CMD_ENABLE_RANGE_RETICLE, /* Turn Ranging Reticle On/Off */
CMD_INIT_NUC_TABLE, /* Initialize NUC table (erase to all 0xFF's) */
CMD_CAMERA_RECOVER, /* Attempt to recover camera from internal errors */
CMD_PLACEHOLDER,
CMD_UPDATE_EXP_PORT, /* Updates Expansion Port Register from CfgData Value */
CMD_UNDEFINED
};
49