CD10022

CD20030

CD10522

CD20530

Kits: Coin Mechanism

 

Kits are available to install a coin mechanism,

a room key mechanism or a key card mechanism. All kits come with detailed instructions which are also listed below.

Please follow these instructions carefully to complete the addition of the coin mechanism kit to the CD10022, CD10522, CD20030, and CD20530 ice dispenser.

1.Disconnect the dispenser from its electrical power supply (failure to do so may result in a serious injury).

Electrical shock hazard. Electrical shock can cause personal injury. Disconnect power before begining to service components.

2.Unlock and remove the decorative front cover, then remove the top front brace and the control box cover.

3.Remove all wires from the push button switch. Now remove the nuts that secure the push button cover from the inside of the dispenser panel.Then remove the cover from the dispenser. Now remove the screws that secure the push button switch to the cover and remove the push button switch.

4.Install the small cover plate which was supplied in the kit.

5.Remove the larger cover plate which is located below where the push button switch was located.

6.Install the mounting plate provided in the kit using the nuts provided in the coin mechanism kit.

7.Secure the coin mechanism to the mounting plate from inside the dispenser cabinet using the screws, flat washers and lockwashers in the kit.

8.Mount the timer and relay from the kit in the control box. (See typical layout of the parts in the following page).

9.Remove wires #8 and #9 from the control box. These wires will be re- placed by different wires which will be identified as #8 and #9.

10.Install the wires provided in the kit following the wiring diagram provided in the kit.

11.Reconnect the electrical power supply to the machine.

12.Place an ice container in the drop zone of the dispenser. Place a quarter into the coin slide mechanism. Then push and hold the safety interlock switch. Now push in the coin mechanism and release it. The dis- penser should dispense ice into the ice container.

13.Determine if the correct amount of ice was dispensed. If more ice is need- ed, increase the time on the timer by turning the timer adjustment dial clockwise. If less ice is required, decrease the time by turning the adjustment knob counter-clock-wise. The initial setting on the timer should be approximately 4 on the knob, approxi- mately 8 seconds. (Each segment on the timer represents approximately

2seconds). IMPORTANT: Make sure to disconnect the power supply to the machine when adjusting the timer.

14.After all adjustments have been completed and the dispenser operates satisfactorily; attach the new electrical schematic over the old one that originally came with the machine and install the coin collection box.

5

Page 6 Page 8
Page 7
Image 7
Ice-O-Matic CD20030 CD20530 installation manual CD10022 CD20030 CD10522 CD20530 Kits Coin Mechanism
Page 6 Page 8

CD20030 CD20530 specifications

The Ice-O-Matic CD20030 and CD20530 are stellar ice machines known for their durability, efficiency, and advanced technology, suited for businesses in need of reliable ice production. These models stand out in the commercial ice-making market due to their robust design and high output capabilities, making them ideal for restaurants, bars, and hotels.

One of the key features of both models is their exceptional ice production rate. The CD20030 produces approximately 2000 pounds of ice per day, while the CD20530 can generate up to 2500 pounds. This high output ensures that businesses can meet their peak demands without compromising service quality. The ice produced is typically in the form of cube ice, which is perfect for beverages and food presentation.

Technologically, the Ice-O-Matic CD series comes equipped with advanced components aimed at enhancing efficiency and reducing energy consumption. The machines utilize a smart technology system that monitors performance and optimizes the ice-making process. This leads to lower energy bills and a reduced environmental impact, aligning with the growing demand for sustainable business practices.

Another significant characteristic of the CD20030 and CD20530 is their easy maintenance. Both models are designed with simple access points, allowing for quick cleaning and servicing. Their self-cleaning features further reduce labor costs, as operators can mitigate the buildup of mineral deposits and bacteria with minimal effort.

The construction of the CD series machines is another highlight. Built with high-quality stainless steel, they are made to withstand the rigors of a busy commercial environment. This material not only enhances durability but also contributes to the machine's resistance to rust and corrosion.

In addition, the Ice-O-Matic machines are designed with user convenience in mind. They feature a straightforward control panel that allows operators to monitor ice production and make any necessary adjustments with ease. Moreover, both models have a compact footprint, making them suitable for establishments with limited space.

In summary, the Ice-O-Matic CD20030 and CD20530 offer powerful ice production capabilities, advanced technological features for efficiency, easy maintenance, and robust construction. These characteristics make them ideal choices for businesses looking for reliable and quality ice machines. With their performance and efficiency, they stand out as exceptional assets in any commercial kitchen or bar setting.
Top Page Image Contents