Optional Accessories Continued

Substrobe DS51

Substrobe DS125

SA-100R

Arm

SA-100R

Arm

EV Controller

 

EV Controller

Substrobe DS51

 

Substrobe DS125

The Substrobe DS51 covers

 

The Substrobe DS125covers

the equivalent of a 28mm

 

the equivalent of a 18mm

lens. It is the ideal c hoice

 

lens, 100 degrees. It is the

when using only the camera

 

ideal choice when using

lens or the camera lens with

 

accessory wide angle lenses

a macro accessory lens.

9

greater than 28mm.

 

 

Quick-Release Base, Handles and Tray

Quick-Release Base

The Quick-Release Base is

 

Quick Release Base

plastic. A toggle lever located

Slot

underneath the base allows

 

 

the base to be easily removed

 

from the Tray. Turn the

 

 

housing upside down, pull

 

 

out on the toggle lever.

 

 

Rotate the lever 90° to

 

 

remove the base.

 

 

Handles and Tray

 

 

The housing handles are

 

 

rubber and the tray is

 

 

aluminum. Their weight

 

 

helps to offset the buoyancy

 

 

of the housing. The complete

 

assembly is slightly negative

 

 

underwater for better

 

 

control. The handles have a

 

 

push button release for easily

 

attaching and removing

 

 

strobe arms. The tray and

 

 

handles can be removed from

 

the housing. To remove the

 

 

tray, the base must be

 

 

removed to gain access to

 

 

the nuts holding the tray on

 

 

the housing. Remove the 2

 

 

nuts, washers and rubber

 

 

spacers. DO NOT remove

 

 

the bolts protruding through

10

 

the housing.

 

Flip Quick Release Lever Up

Rotate Quick Release Lever

Remove Quick

Release Lever

and Base

Maintenance

 

The Ikelite Digital Housing should be given the same care and

 

attention as your other photographic equipment. In addition to

 

normal maintenance we recommend that the housing be returned

to Ikelite periodically to be checked and pressure tested.

 

1.

Do Not leave the camera and housing in direct sunlight for

 

2.

prolonged periods. Heat may damage the camera.

 

Do Not ship the camera in the housing.

 

3. Before using the housing, always check the tightness of the

 

 

set screw in each control knob.

 

 

Check each control gland penetrating the housing to make sure

 

they are tight. There is a slight chance that either could vibrate

 

loose during travel.

 

4. Keep the back o’ring clean and lightly lubricated. To lubricate

 

 

remove the o’ring from the back. Put a small amount of lkelite

 

lubricant on your fingers. Draw the o’ring through your fingers

 

to apply a light coating of lubricant. Only apply enough

 

 

lubricant to make the o’ring feel slick. Do Not stretch the o’ring.

 

This light coating of lubricant will help to keep the o’ring from

 

drying out and will help to show a dark sealing line when the

 

 

housing back is properly sealed.

 

5. Keep the area where the o’ring fits and the sealing surface of

 

 

the housing clean.

 

6. Rinse the housing exterior thoroughly in fresh water after each

 

 

salt water use. Dry with a soft cloth. Dry lens port toeliminate

 

 

water spotting.

 

 

After several uses in salt water soakthe housing in a mild soap

 

 

solution, rinse and dry before storage. When storing the housing,

 

 

remove the back o’ring, lightly ubricatel and place in a plastic bag.

 

Place the plastic bag with o’ring inside the housing for safe keeping.

CAUTION

 

 

Never use spray lubricants as the propellant ingredient can

11

 

cause the plastic housing to crack.

Control Maintenance

Ikelite controls are designed to provide years of reliable service with minimal maintenance.

1. Push button controls require no maintenance other than rinsing in fresh water after saltwater use. If a push button control becomes difficult to push or if it sticks when depressed, soak the housing in luke warm fresh water. After a few minutes operate the push button. If this does not correct the problem, return the housing to Ikelite for maintenance.

2. Some of the controls have long shafts. These controls can be

lubricate shaft

housing

pull out to expose shaft

pulled out, exposing the shaft (see drawing).

To lubricate the control, gently pull on the knob until the stainless steel shaft is exposed. Lightly lubricate the shaft, then move the shaft in and out several times. This will lubricate the x’ring in the Ikelite control gland. This should be done before using the housing after a prolonged storage period, or once a week when the housing is in use.

12

Page 3
Image 3
Ikelite DSC-H7 Optional Accessories, Substrobe DS51 Substrobe DS125, Quick-Release Base, Handles and Tray, Maintenance