HOT PARTS mm600

Gas connection

GB

The cooker should be connected to the gas-supply by a corgi registered installer. During installation of this product it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience of any subsequent removal or servicing. Connection of the appliance to the gas mains or liquid gas must be carried out according to the prescribed regulation in force, and only after it is ascertained that it is adaptable to the type of gas to be used. If not, follow the instructions indicated in the paragraph headed “Adaptation to different gas types”. On some models the gas supply can be connected on the left or on the right, as necessary; to change the connection, reverse the position of the hose holder with that of the cap and replace the gasket (supplied with the appliance). In the case of connection to liquid gas, by tank, use pressure regulators that conform to the regulation in force. The gas supply must be connected to the left of the appliance. Be sure that the hose does not pass through the rear of the cooker touching hot parts.

￿make sure the supply pressure conforms with the values shown in the table entitled “Caracteristics of the burners and nozzles”. When the cooker is installed between cabinets (recessed), the gas connection must be effected by an approved flexible hose with bayonet fitting (BS 669 Current Edition). The gas inlet for the cookers is a threaded G 1/2 gas female fitting.

Connecting the gas supply

To make the connection, a flexible hose should be used corresponding to the current gas regulations which are:

• the hose must never be at any point in its lenght in contact with the “hot” parts of the cooker;

•the hose must never be longer than 1,5 metre;

•the hose must not be subject to any tension or torsional stress and it must not have any excessively narrow curves or bottlenecks;

•the hose must be easy to inspect along its entire length to check its condition;

•the hose must always be in good condition, never attempt to repair.

￿the installation must comply with gas safety (installation and use) regulations 1984. In all cases for the above, by low, a qualified, corgi approved

engineer must be called for installation.

Electrical connection

Power supply voltage and frequency: 230-240V a.c. 50Hz.

￿the supply cable must be positioned so that it never reaches at any point a temperature 50°C higher than the room temperature. The cable must be routed away from the rear vents. Should you require it, you may use a longer cable, however, you must ensure that the cable supplied with the appliance is replaced by one of the same specifications in accordance with current standards and legislation.

Your appliance is supplied with a 13 amp fused plug that can be plugged into a 13 amp socket for immediate use. Before using the appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse

When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362 should always be used, and the fuse cover re-fitted. If the fuse cover is lost, the plug must not be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug. Replacements can be obtained directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug and you should wish to remove it to add a cable extension or to re-route the mains cable through partitions, units etc., please ensure that either:

• the plug is replaced by a fused 13 amp re- wireable plug bearing the BSI mark of approval.

or:

•the mains cable is wired directly into a 13 amp cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible without moving the appliance.

Please note: for appliances with a rating greater

than 13 amp (eg: electric hob, double ovens and freestanding electric cookers etc.) the mains cable must be wired into a cooker output point with a

4

Page 4 Page 6
Page 5
Image 5
Indesit KD3G specifications Gas connection, Electrical connection
Page 4 Page 6

KD3G specifications

The Indesit KD3G is a versatile and user-friendly gas cooker that combines functionality with a modern design, making it an ideal addition to any kitchen. With a capacity to enhance culinary experiences, this stove is built for efficiency and convenience, appealing to both beginner cooks and seasoned chefs alike.

One of the standout features of the Indesit KD3G is its four gas burners, which provide ample cooking space for multiple dishes. The burners come in various sizes, allowing users to choose the appropriate heat level for different cooking tasks, from simmering sauces to boiling pasta. The high-efficiency burners ensure optimal heat distribution, which is essential for consistent cooking results.

This model is equipped with a conventional oven, offering a spacious 58-liter capacity. The oven is perfect for a range of cooking methods, including baking, roasting, and grilling. Its easy-to-use controls allow for precise temperature settings, ensuring your dishes are cooked to perfection every time. Additionally, the oven features a double-glazed door that helps retain heat while allowing visibility of the cooking process without having to open the door.

One of the key technologies integrated into the Indesit KD3G is the flame safety device. This safety feature automatically cuts off the gas supply if the flame goes out, providing peace of mind to users and ensuring a safe cooking environment. The appliance also comes with a sleek and easy-to-clean enamel finish, which simplifies maintenance and extends the appliance's lifespan.

The Indesit KD3G is designed with practicality in mind. Its adjustable feet allow for stability on various kitchen surfaces, while the integrated storage compartment provides a convenient space for keeping cooking essentials close at hand. The cooker also boasts an easy-to-read control panel, making it simple to operate even for those unfamiliar with gas appliances.

In conclusion, the Indesit KD3G gas cooker is a well-designed kitchen essential that combines safety, efficiency, and style. Its intuitive features and robust performance make it an excellent choice for anyone looking to elevate their cooking experience. Whether you're whipping up a family meal or preparing a feast for friends, the Indesit KD3G delivers results that satisfy.
Top Page Image Contents