CCN 99449712

OPERATOR’S MANUAL 66605X-X

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

1/2” DIAPHRAGM PUMP

1:1 RATIO (NON-METALLIC)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

SERVICE KITS

Refer to Model Description Chart to match the pump material options.
637140-XX for fluid section repair (see page 4).
637141 for air section repair (see page 6).

PUMP DATA

Models see Model Description Chart for “-XXX”...........
Pump Type Non-Metallic Air Operated Double Diaphragm.......
Material see Model Description Chart...........
Weight Polypropylene 7.2 (3.3 kgs).... .........
Groundable Acetal 8.8 (4.0 kgs)......
KynarRPVDF 9.5 (4.3 kgs).........
Maximum Air Inlet Pressure 100 p.s.i.g. (6.9 bar).........
Maximum Material Inlet Pressure 10 p.s.i.g. (0.69 bar).....
Maximum Outlet Pressure 100 p.s.i.g. (6.9 bar)..........
Air Consumption 1 c.f.m. / gallon (approx.).................
Maximum Flow Rate (Ball) 13 g.p.m. (49.2 l.p.m.).......
(Duckbill) 10 g.p.m. (37.9 l.p.m.)....
Maximum Particle Size (Ball) 3/32” dia. (2.4 mm).......
(Duckbill) Fibers....
Maximum Temperature Limits
E.P.R. -60_to 280_F(-51_to 138_C)................
Groundable Acetal 10_to 180_F(-12_to 82_C).......
HytrelR-20_to 150_F(-29_to 66_C)..............
Neoprene 0_to 200_F(-18_to 93_C).............
Nitrile 10_to 180_F(-12_to 82_C)................
Polypropylene 35_to 175_F(2_to 79_C)..........
Polyurethane 10_to 150_F(-12_to 66_C)...........
Kynar PVDF 10_to 200_F(-12_to 93_C)...........
SantopreneR-40_to 225_F(-40_to 107_C)..........
PTFE 40_to 225_F(4_to 107_C)................
VitonR-40_to 350_F(-40_to 177_C)...............
Groundable 666056-X and 66605H-X models only...........
Dimensional Data see page 8................
Noise Level @ 70 p.s.i., 60 c.p.m. 71.1 db(A).....
* The pump sound pressure levels published here have been updated to an Equivalent
Continuous Sound Level (LAeq) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-
ROP S5.1 using four microphone locations.
NOTICE: All possible options are shown in the chart however certain com-
binations may not be recommended, consult a representative or the fac-
tory if you have questions concerning availability.
666053-XXX
666056-XXX
666057-XXX
66605J-XXX
66605H-XXX
66605K-XXX Figure 1

MODEL DESCRIPTION CHART

66605 X -X X X - 04

66605X - X X X
637140 - X X
DiaphragmBall
FLUID SECTION SERVICE KIT SELECTION
EXAMPLE: MODEL # 666053-321
Fluid Section Service Kit # 637140-21
Seat Material
0 - (Duck Bill) 4 - Kynar PVDF
2 - Stainless Steel 6 - Acetal
3 - Polypropylene
Ball Material ( * ) Duckbill models
1 - Neoprene 8 - Polyurethane
2 - Nitrile A - Stainless Steel
3 - Viton C - Neoprene (*)
4 - PTFE D - Nitrile (*)
5 - E.P.R. E - Santoprene
Diaphragm Material
1 - Neoprene 5 - E.P.R.
2 - Nitrile 8 - Polyurethane
3-Viton 9-Hytrel
4 - PTFE / Santoprene B - Santoprene
Fluid Caps & Manifold Material
3 - Piece Manifold Single Piece Manifold
3 - Polypropylene J - Polypropylene
6 - Groundable Acetal H - Groundable Acetal
7 - Pure Kynar K - Pure Kynar
Cone Check Flow
04 - Top Discharge
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276 FAX(800) 892-6276 © 2012
www.ingersollrandproducts.com
RELEASED: 4-15-87
REVISED: 1-23-12
(REV. AS)