Ingersoll-Rand 66615X-X-C manual Ratio Metallic, Service Kits, Pump Data, Model Description Chart

OPERATOR’S MANUAL 66615X-X-C

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

1-1/2” DIAPHRAGM PUMP

1:1 RATIO (METALLIC)

RELEASED: 5-31-88

REVISED: 12-1-10(REV. AB)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

SERVICE KITS

Refer to the Model Description Chart to match the pump material op- tions.

637118-C for air section repair (see page 6).

637124-XX for fluid section repair (see page 4).

637155 Abrasion Resistant Conversion Kit is available for use in heavy and abrasive material applications (see page 4).

	PUMP DATA
Models . . . .	. . . . . . . . see “Model Description Chart” for “-XXX”
Pump Type .	. . . . . . . . Metallic Air Operated Double Diaphragm
Material . . . .	. . . . . . . . see “Model Description Chart”
Weight . . . .	Aluminum	51.54 lbs (23.4 kgs)
	Cast Iron	79.54 lbs (36.1 kgs)
	Stainless Steel	84.54 lbs (38.3 kgs)
	[add 23 lbs (10.4 kgs) for cast iron air motor section]
Maximum Air Inlet Pressure		120 p.s.i. (8.3 bar)
Maximum Material Inlet Pressure . . . .		10 p.s.i. (0.69 bar)
Maximum Outlet Pressure		120 p.s.i. (8.3 bar)
Maximum Flow Rate (flooded inlet) . . . .		90 g.p.m. (340.7 l.p.m.)
Displacement / Cycle @ 100 p.s.i.g. . .		0.64 gal. (2.42 lit.)
Maximum Particle Size		1/4” dia. (6.4 mm)

Maximum Temperature Limits (diaphragm / ball / seat material)

Acetal	10_ to 180_ F (-12_to 82_ C)
E.P.R	-60_to 280_F (-51_to 138_C)
HytrelR	-20_to 150_ F (-29_to 66_ C)
KynarR PVDF	10_ to 200_ F (-12_to 93_ C)
Neoprene	0_ to 200_ F (-18_to 93_ C)
Nitrile	10_ to 180_ F (-12_to 82_ C)
Polypropylene	35. ._ to 175_ F (2_ to 79_ C)
Polyurethane	10_ to 150_ F (-12_to 66_ C)
PTFE	40_ to 225_ F (4_ to 107_ C)
SantopreneR	-40_to 225_F (-40_to 107_C)
VitonR	-40_to 350_F (-40_to 177_C)
Dimensional Data	. . see page 8

Noise Level @ 70 p.s.i. - 60 c.p.m. . . 77.7 dba(A)

Tested with 93139 muffler assembly installed.

The pump sound pressure levels published here have been updated to an Equivalent

Continuous Sound Level (LAeq) to meet the intent of ANSI S1.13-1971, CAGI-PNEU- ROP S5.1 using four microphone locations.

NOTICE: All possible options are shown in the chart. However, certain combinations may not be recommended, consult a representative or the factory if you have questions concerning availability.

	66615X-XXX-C				Figure 1
1-1/2” DIAPHRAGM PUMP
	MODEL DESCRIPTION CHART
				6661 X X - X X X - C
Center Body Material, Threads
5	- Aluminum, N.P.T.F.	7	- Aluminum, BSP
6	- Cast Iron, N.P.T.F.	8	- Cast Iron, BSP
Fluid Cap / Manifold Material, Hardware
	(Steel Hardware)	(Stainless Steel Hardware)
0	- Aluminum	A - Aluminum
1	- Stainless Steel	B - Stainless Steel
2	- Cast Iron	C - Cast Iron
Seat Material
1	- Aluminum	4	- Kynar PVDF
2	- 316 Stainless Steel	5	- Carbon Steel
3	- Polypropylene	8	- 440 Stainless Steel
Ball Material
1	- Neoprene	6	- Acetal
2	- Nitrile	8	- Polyurethane
3	- Viton	A - Stainless Steel
4	- PTFE	C - Hytrel
5	- E.P.R.	E - Santoprene
Diaphragm Material
1	- Neoprene	5	- E.P.R.
2	- Nitrile	9	- Hytrel
3	- Viton	B - Santoprene
4	- PTFE / Santoprene

FLUID SECTION SERVICE KIT SELECTION	6661XX - X X X - C
EXAMPLE: MODEL # 666150-361-C	637124 - X X
FLUID SECTION SERVICE KIT # 637124-61
	Ball	Diaphragm

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET -- BRYAN, OHIO 43506

(800) 276-4658 D FAX (800) 266-7016 E2010 CCN 81660219

www.ingersollrandproducts.com