Ingersoll-Rand PE10X-X-X manual Read This Manual Carefully Before Installing, Service Kits

OPERATOR’S MANUAL	PD10X-X-X
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE	PE10X-X-X
1” DIAPHRAGM PUMP	RELEASED: 3-11-04
	REVISED: 11-11-10
1:1 RATIO (METALLIC)	(REV. 08)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

SERVICE KITS

Refer to Model Description Chart to match the pump material options. 637397 for air section repair (see page 6).

637401-XX for fluid section repair (see page 4). NOTE: This kit also con- tains several air motor seals which will need to be replaced.

637395-X major air valve assembly (see page 7).

PUMP DATA

Models	see Model Description Chart for “-XXX”
Pump Type	Metallic Air Operated Double Diaphragm
Material	see Model Description Chart

Weight . . .	PX10R-XAX-XXX	20.65 lbs (9.37 kgs)
	PX10R-XCX-XXX	35.2 lbs (16.0 kgs)
	PX10R-XHX-XXX	39.6 lbs (18.0 kgs)
	PX10R-XSX-XXX	38.2 lbs (17.3 kgs)
	add 4.65 lbs (2.11 kg) for Aluminum air motor section
	add 11.09 lbs (5.03 kg) for Stainless Steel air motor section

Figure 1

MODEL DESCRIPTION CHART

Maximum Air Inlet Pressure	120 p.s.i.g. (8.3 bar)
Maximum Material Inlet Pressure	10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure	120 p.s.i.g. (8.3 bar)
Maximum Flow Rate (flooded inlet) . . . .	52.2 g.p.m. (197.6 l.p.m.)
Displacement / Cycle @ 100 p.s.i.g. . . .	0.232 gal. (0.88 lit.)
Maximum Particle Size	1/8” dia. (3.3 mm)

Maximum Temperature Limits (diaphragm / ball / seal material)

E.P.R. / EPDM	-60_to 280_F (-51_to 138_C)
HytrelR	-20_to 150_ F (-29_to 66_ C)
Nitrile	10_ to 180_ F (-12_to 82_ C)

Electronic Interface

D - None E - Available

Center Section Material

A - Aluminum

R- Polypropylene S - Stainless Steel

Fluid Connection

A- 1 -- 11-1/2 N.P.T.F. - 1 B - 1 -- 11 BSP

P X 10 X - X X X - X X X

Polypropylene	. 35_ to 175_ F (2_ to 79 _ C)
SantopreneR	. -40_to 225_F (-40_to 107_C)
PTFE	. 40_ to 225_ F (4_ to 107_ C)
VitonR	. -40_to 350_F (-40_to 177_C)
Dimensional Data	. . . . . . see page 8
Mounting Dimension	4” x 6.25” (101.6 mm x 158.8 mm)
Noise Level @ 70 p.s.i., 60 c.p.m.	. . . . . 80.6 db(A){

The pump sound pressure levels published here have been updated to an Equivalent

Continuous Sound Level (LAeq) to meet the intent of ANSI S1.13-1971, CAGI-PNEU- ROP S5.1 using four microphone locations.

NOTICE: All possible options are shown in the chart, however, certain combinations may not be recommended, consult a representative or the factory if you have questions concerning availability.

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET- BRYAN, OHIO 43506

(800) 276-4658 D FAX (800) 266-7016 E2010 CCN 15207657

www.ingersollrandproducts.com

Fluid Caps & Manifold Material
A	- Aluminum		H - Hastelloy - C
C	- Cast Iron		S	- Stainless Steel
Hardware Material
P	- Plated Steel		S	- Stainless Steel
Seat Material
A	- Santoprene		G	- Nitrile
C	- Hytrel		H - Hard 440 Stainless Steel
E	- Carbon Steel		L	- Hastelloy - C
F	- Aluminum		S	- 316 Stainless Steel
Ball Material
A	- Santoprene		S	- 316 Stainless Steel
C	- Hytrel		T	- PTFE
G	- Nitrile		V	- Viton
Diaphragm Material
A	- Santoprene	M	- Medical Grade Santoprene
C	- Hytrel	T	- PTFE / Santoprene
G	- Nitrile	V	- Viton

FLUID SECTION SERVICE KIT SELECTION	PX10X - XXX - X X X
EXAMPLE: Model # PD10A-ASP-AAA	637401 - X X
Fluid Section Service Kit # 637401-AA	Ball	Diaphragm