Insignia
4 Press and hold the SET button on the remote | Programming the volume lock | |||
| control until the LED blinks twice, then | The remote control comes preset to let you | ||
| release the button. | |||
| control the volume of each connected device. | |||
5 Enter the first | ||||
You can change the volume lock so that one | ||||
| The LED blinks once as each digit is entered. | device’s volume controls volume in all modes. | ||
| If the code is correct, the LED blinks twice. | After you lock the volume control, you can unlock | ||
|
|
| the volume control for a specific device so you | |
| Note | can control the volume for that device | ||
|
| If the LED does not blink twice, repeat steps 3 | independently. | |
|
| through 5 using a different code. |
| |
|
|
| To lock the volume control: | |
6 Aim the remote at the device, then press the | ||||
|
| button.The device should turn off. | 1 Press and hold the SET button until the LED | |
|
| |||
|
| |||
|
|
| blinks twice, then release the button. | |
Note
If the device does not turn off, repeat steps 4 through 6 using a different code. If you cannot find a code that works, see “Searching for a code” on page 17.
7Repeat steps 1 through 6 to program additional devices.
8Press the SET button to save the code and exit.
Searching for a code
To search for a code:
1Press a device key.
2Press and hold the SET button until the LED blinks twice, the release the button.
3Enter 991, then the device group number (0=cable, 1=TV, 2=VCR, 3=audio). The LED blinks twice.
4Aim the remote control at the device, then
press the 
button. If the device responds, go to step 7.
5If the device does not respond, press the CH+ button. Your remote control will try the next code. Keep pressing the CH+ button until the device responds. You can press the CH– button to try a previous code.
6To search for a code for another device, repeat steps 1 through 5.
7Press the SET button to save the code and exit.
Checking the code
If you programmed a device by searching for a code, you may want to know what
To check the code:
1Press the device button on the remote control.
2Press and hold the SET button until the LED blinks twice, then release the button.
3Enter 990. The LED blinks twice.
4Press 1 and count the LED blinks. This is the first digit of the code. For example, if the LED blinks twice, the first digit is 2. If the LED does not blink, the first digit is 0.
5Repeat step 4 using 2 for the second digit, 3 for the third digit, 4 for the fourth digit, and 5 for the fifth digit.
6Press the SET button to exit.
2Enter 993, then press the device button for the device you want to control the volume. The LED blinks twice. When you press the VOL+,
To unlock the volume control:
1Press and hold the SET button until the LED blinks twice, then release the button.
2Enter 993, then press VOL+ button. The LED blinks four times. The volume control is unlocked.
To unlock a single device’s volume control:
1Press the device key.
2Press and hold the SET button until the LED blinks twice, then release the button.
3Enter 993, then press VOL– button. The LED blinks four times. The volume control for the device you selected is unlocked.
Troubleshooting the remote control
Symptom | Possible solution |
|
|
LED does not blink when | Replace the batteries. |
a button is pressed |
|
|
|
LED blinks when a | Make sure that you are at less than 15 |
button is pressed, but | feet (4.6 meters) from the device and |
device does not respond | that you point the remote control at the |
| remote sensor on the device. |
|
|
LED blinks one long | You pressed an incorrect button. Start |
blink | the procedure over again. |
|
|
Remote control does not | Make sure that the device has a remote |
control a device or only | sensor, then try another code. |
controls some features |
|
of the device |
|
|
|
No volume on a device | See “Programming the volume lock” |
| on page 17. |
17 | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
