CARE AND USE

Electric Shock Hazard: To prevent electrical shock, disconnect power before servicing unit. Use only a properly grounded and polarized electric outlet.

ADJUSTING THE THERMOSTAT

Factory temperature pre-set is

approx. 200°

200˚F. To reset the thermostat

 

to 200°, turn the indicator two

 

notches to the right of vertical.

 

■ Adjust the thermostat slowly, turning the dial

clockwise to increase

temperature or counter clockwise to decrease temperature, then activate faucet handle for 20 seconds to bring in fresh water to be heated at the new setting. Allow 5-7 minutes for water to reach new temperature.

Scalding Hazard: Do not allow

water to boil. May result in severe burns.

SEASONAL STORAGE/DRAINAGE

Anytime the instant hot water dispenser is not used for extended periods of time, unplug and drain unit. If it is below freezing you will need to unplug the unit and drain it.

Disconnect power from unit.

Push hot water dispenser faucet lever and allow water to flow until it is cool.

Shut the cold water supply off at the valve.

Locate and remove drain screw from bottom center of water tank and drain the water into empty pail.

Empty the tank and then reinstall drain screw into the bottom of tank, turning until snug. Do NOT over tighten.

Remove and discard filter cartridge.

To put back into working order, install new filter cartridge, fill tank with water and reconnect the electrical cord. (Refer to Page 9, Step 6B)

CLEANING THE FAUCET AND TANK

Only use mild cleaners to clean the faucet and plastic components.

Cleaners with acids, abrasives, alkaline or organic solvents will result in deterioration of the plastic components and void the warranty.

FILTER GUIDE AND REPLACEMENT

Replace filter cartridge when there is an obvious decrease in water flow to the faucet or if there is an objectionable taste or odor to the water.

When the inlet and outlet ports have been closed and the filter’s internal pressure has been relieved, water (about 2 oz) will discharge from vent line.

If the new filter cartridge cannot be inserted, insert the old one and turn until it stops, remove it and then retry the new cartridge.

Carbon filters should be replaced within 12 months.

Filter replacement instructions:

Replace with an InSinkErator® filter.

Place pan or dish towel under the filter to catch water drainage during change.

Slowly turn the cartridge counter-clockwise completely until it stops (1/4 turn).

Pull cartridge straight down and discard.

Insert new cartridge into filter head.

Top surface of cartridge will become flush with the bottom of the filter head when fully engaged.

Turn the cartridge clockwise until it stops (1/4 turn).

Align the in/out arrow on the head and bracket assembly to the in/out arrow on the cartridge.

Open faucet to expel trapped air.

Run water for 3 minutes before usage.

PROPERTY DAMAGE

Regularly inspect the unit for any signs of leakage. If there are signs of water damage, immediately remove the unit from service.

To avoid water damage from leakage, replace all cut, loose or split tubing.

A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any leakage could cause property damage.

12

Page 12
Image 12
InSinkErator 1100 owner manual Care and USE, Factory temperature pre-set is, Disconnect power from unit

1100 specifications

The InSinkErator 1100 is a popular model among household garbage disposals, celebrated for its robust construction and efficient performance. Ideal for homeowners who prioritize convenience and cleanliness in their kitchens, the 1100 model excels in efficiently disposing of food waste, thus promoting a hygienic cooking environment.

One of the standout features of the InSinkErator 1100 is its powerful grinding capability. Equipped with a 0.75 HP motor, this unit can easily accommodate a wide variety of food scraps, including fibrous vegetables, bones, and even small fruit pits. This high torque ensures that everything is pulverized quickly, allowing for smooth drainage and minimal clogging. Additionally, the grinder operates quietly, thanks to its anti-vibration design, which is a significant advantage in homes with open kitchen layouts.

The InSinkErator 1100 also incorporates advanced technologies to enhance its efficiency and durability. The GrindShield technology is a notable feature, which helps to reduce wear and tear on the grinding components and prolongs the lifespan of the unit. Moreover, the permanently lubricated motor not only ensures a quieter operation but also eliminates the need for routine maintenance, making it a hassle-free choice for users.

Ease of installation is another characteristic that sets the InSinkErator 1100 apart from other models. With a straightforward design and compact size, it easily fits under most kitchen sinks. The unit comes with a comprehensive installation kit, ensuring that homeowners can set it up without professional help, saving both time and money.

In terms of safety, the 1100 model is designed with a manual reset button in case of overload, providing an extra layer of protection against potential hazards. Additionally, its stainless-steel grinding components are resistant to corrosion, ensuring reliable performance and maintenance of hygiene standards over the years.

The InSinkErator 1100 ranks as an excellent choice for those looking to invest in a durable, high-performance garbage disposal system. Its combination of strength, efficiency, and user-friendly features makes it a highly regarded option among homeowners seeking to upgrade their kitchen appliances for improved waste management.