Manuals / Intel / Computer Equipment / Switch

Intel EE110MM manual OK: The port is functioning normally

Models: EE110MM

1 61

Download 61 pages 22.69 Kb

Page 28

OK: The port is functioning normally.

Port: Displays the port number on the hub selected in the Hub: field. Ports 13-Slotand 14-Sloton a 12-port hub refer to the two expansion slots. If you’re facing the hub, the left slot is port 13 and the right slot is port 14.

13-slot14-slot

Intel Express

Management Module

Esc

10/100 Stackable Hub

Main Menu:

Change hub speed

10BASE-T

Collision

Power

Stats Config

>

Reset

100BASE-TX

Managed

Status

1

2

3

4

5

6

7

8

9

10

11

12

Green (left)

Solid = Link

Blink = Activity

Amber (right)

Solid = Disabled

Blink = Wrong Speed

Status: Displays the current functional state of the port. Possible values are:

OK: The port is functioning normally.

disabled: The port was manually disabled (see Disable/ enable port). The port cannot establish a link with a device again until it’s enabled.

partitioned: The port was automatically disabled by the hub due to an error condition, such as 64 consecutive collisions. The port will be automatically enabled when the condition clears.

wrong speed: The device attached to the hub is operating at 10 Mbps while the hub is operating at 100 Mbps, or vice-versa.

Link: Indicates whether a device is properly connected to the port.

27

Image 28

Intel EE110MM manual OK: The port is functioning normally

Contents

Management Module Intel Express 10/100 Stackable HubUser Guide First edition July669884-001 This guide covers the following productQuick Start Turn on the power after installingContents Using the LCDUsing the Console Manager ChapterTechnical Information IndexContacting Intel Customer Support Inside back coverOverview of Hub ManagementManaging multiple hubs Hub numberingCollision domain assignments MIB identification100Mbps 100Mbps 10Mbps 10MbpsConfig Set IP address Manual BootP SleepLCD menu tree Stats2 Using the LCD Reset button. See pageNavigating Esc - use to go back a levelChanging the LCD contrast Viewing statisticsDomain PortChanging the IP configuration Setting the sleep modeSetting the serial port baud Disabling a portViewing trap messages Viewing About informationUsing the Console Manager Accessing with the serial portEnter EnterAccessing with Telnet telnet ETo use Telnet EnterToggling between insert and overstrike mode NavigatingTop screen main To return to the Top screen at any time, press cTSystem Configuration screen Top screen 1. System ConfigurationLocation UsesHub 1 of Hub 2 of Hub 3 of Hub 4 of in the stack has no effect on hub numberingLocal IP Configuration screen Top screenLocation UsesIP address: The unique user-assignednetwork address for the Management Module Remote IP Configuration screen LocationUses Top screen•Press <CANCEL> to return to the previous menu SNMP Configuration screen 1.System Configuration <SNMP configuration>Location UsesTrap Receiving Stations screen <Define trap receiving stations>1.System configuration <SNMP configuration> LocationSupported traps include Port Configuration screen Top screen 2. Port configurationLocation UsesOK: The port is functioning normally Collision Domain Statistics screen Top screen 3. Collision domain statisticsLocation Uses100Mbps 100Mbps 10Mbps 10Mbps100Mbps collision domain 10Mbps collision domainFrames too long: The number of frames detected that exceed the maximum permitted frame size of 1518 octets Port Statistics screen traffic LocationUses Top screenStatistic: Use ASor zto select the type of port statistics you want to view. Errors is the other type of statistic option you can view. See page Port Statistics screen errors 4.Port statistics Statistic: errorsLocation UsesStatistic: Use ASor zto select the type of port statistics to view. Traffic is the other type of statistic option you can view see page Late events: The number of collisions detected after the allowable detection period. Usually indicates a network topology problem, such as daisy-chainingtwo Express hubs running at 100 Mbps with UTP cable instead of Intel Cascade Cables in a stack, daisy-chainingtoo many hubs running at 10 Mbps, or using cables longer than 100 meters Network Health Checks screen Top screen 5. Network health checksLocation UsesWrong Speed Device screen LocationUses Top screenPage Wrong Polarity Cabling screen <Check for wrong polarity cabling to devices>Location UsesPage Top Traffic Generators screen LocationUses Top screenUpdate interval: Selects the time period between updates. For example, an Update interval of 5 sec. means the Console Manager checks the Management Module every five seconds for the list of devices that are generating the most traffic Utilization and Collision History screen LocationUses Top screenInterpreting this screen Login, Security & Reset Options screen Top screen 6. Login, security, and reset optionsLocation UsesFront panel reset button ResetAbout screen Top screen 7. AboutLocation UsesProduct name: Displays the type of device the Management Module is supporting Logout screen Top screen 8. LogoutLocation UsesTechnical Information DefaultsLocating MIB files Console Manager Returning a Defective Product RMA Limited Hardware WarrantyLIMITATION OF LIABILITY AND REMEDIES Manufacturer Declaration Federal Communications Commission FCC StatementAVERTISSEMENT AVVERTENZA WARNUNGADVERTENCIAS I Index Page Page Page Page Troubleshooting Software updatesInstallation notes How to access