Manuals / Intel / Computer Equipment / Printer

Intel MIC-3358 user manual Installing CPU and Heat Sink

Models: MIC-3358

1 84

Download 84 pages 63.27 Kb

Page 30

1.To avoid electric shock, always disconnect the power from your PC chassis before you work on it. Don't touch any components on the CPU card or other cards while the PC is on.

2.Disconnect power before making any configuration changes. The sud- den rush of power as you connect a jumper or install a card may damage sensitive electronic components.

3.Always ground yourself to remove any static charge before you touch your CPU card. Be particularly careful not to touch the chip connectors. Modern integrated electronic devices, especially CPUs and memory chips, are extremely sensitive to static electric discharges and fields. Keep the card in its antistatic packaging when it is not installed in the PC, and place it on a static dissipative mat when you are working with it. Wear a grounding wrist strap for continuous protection.

1.7Installing CPU and Heat Sink

The MIC-3358 supports Intel® Pentium® 4 processor - M . In order to meet critical environmental conditions and the physical space of the MIC-3358 at the same time, Advantech designed a heat sink to fulfill its primary needs. Please refer to Figure 1-4 for an illustration of the heat sink used for the MIC-3358.

The small aluminum plate is default fastened on the CPU in the factory.

When user doing the memory installation, the following steps should be followed:

1.Remove the screws for the solder side cover. At this step, the front panel will be also loose. Be careful about any improper disassemble pro- cedure that could cause any damage of SBC.

2.Remove the rest four screws for heatsink standing, then the heat- sink is loose for memory installation and relavant.

3.Follow the opposed procedure to assembly the heatsink and solder side cover.

Note: The heat pad is sealed between heatsink and CPU is kind of frangible, please be careful on the disassemble procedure. And be careful with any other damage of heat pad will cause the thermal issue easily.

MIC-3358 User’s Manual

22

Image 30

Intel MIC-3358 user manual Installing CPU and Heat Sink

Contents

User’s Manual MIC-3358VGA / Dual Giga LAN / PMC Technical Support and Sales Assistance Copyright NoticeAcknowledgements http//support.advantech.com.twProduct warranty CE NotificationPacking List Chapter Hardware ConfigurationChapter 2 Connecting Peripherals ContentsVGA Display Connector CN9 or Rear I/O ChapterAppendix Award BIOS SetupAppendix A Pin AssignmentsJ2 Connector Hardware Configuration CHAPTERHigh Performance Intel Pentium 4 Processor -M Chapter 1 Hardware Configuration1.1 Introduction Compact Mechanical DesignComplete I/O Functions 1.2 SpecificationsPMC PCI Mezzanine Card IEEE1386.1 Compliant Standard SBC FunctionsPCI-to-PCI Bridge 10/100/1000Base-TX Ethernet InterfacePCI VGA Interface Controller ATI Rage XL Operating temperature 0 ~ 55 C 32 ~ 131 F Display memory 8MB SDRAM VRAM Display Resolution Number of ColorsMechanical and Environmental Specifications Optional Rear I/O Boards1.4 Jumpers 1.3 Functional Block DiagramFigure 1.1 MIC-3358 functional block diagram 1.4.1 Jumper LocationsTable 1.3 JP2 jumper definitions PMC Module Voltage Vio 1.4.2 Clear CMOS JP4Table 1.2 JP1 jumper definition PMC Module Voltage Vi/o Table 1.4 JP7 jumper definitions CompactFlash card1.5 Connectors Table 1.6 MIC-3358 connector descriptionsTable 1.5 Clear CMOS JP4 Table 1.7 CN1 IDE Connector Definitions Chapter1Table 1.8 CN2 CompactFlash Socket Definitions MIC-3358 User’s ManualTable 1.9 CN3 RJ-45 COM1 port Definitions Pin SignalChapter1 Pin 1-2 handle closed Table 1.10 CN4 Handle Switch DefinitionsFigure 1.2 Handle Switch Definitions Pin 1-3 handle openSignal Table 1.11 CN5 USB 1.1/2.0 port DefinitionsTable 1.12 CN6 USB 1.1/2.0 port Definitions Pin SignalSignal Table 1.13 CN9 DB-15 VGA Connector DefinitionsTable 1.14 PU1 Gigabit LAN Connector Definitions PinSignalJ11 PIN SIGNAL Table 1.15 J11/J12/J14 PMC Connector DefinitionsThe LED indicator means Chapter1PIN# J12 PIN SIGNALMIC-3358 User’s Manual Single NamePIN# J14 Pin SignalChapter1 Single NameTable 1.16 D9 LED Definitions Table 1.17 SW1 Vcore selection definitionsMIC-3358 User’s Manual Table 1.18 SW2 Drone mode definitions SW2 ONChapter1 Figure 1.3 MIC-3358 jumper and connector locations Please refer to Appendix B for J1/2/3/5 pin assignmentsMIC-3358 User’s Manual 1.6 Safety Precautions Figure 1.4 MIC-3358 front panel connector and indicator locationsChapter1 1.7 Installing CPU and Heat Sink Figure 1.5 Complete assembly with heat sink and hard disk 1.8 Software supportChapter1 MIC-3358 User’s Manual Connecting Peripherals CHAPTER2.3 PS/2 Keyboard and Mouse Connector Rear I/O Chapter 2 Connecting Peripherals2.2 VGA Display Connector CN9 or Rear I/O 2.1 IDE Device CN1 and Rear I/O2.5 Ethernet Configuration PU1 , Rear I/O and J3 Table 2.1 MIC-3358 serial port default settings2.4 Serial Ports CN3 and Rear I/O 2.9 Card Installation 2.6 USB Connector CN5/6 and Rear I/O2.7 PMC Connector J11, J12, J14 2.8 CompactFlash Socket CN2To install a card To remove a cardMIC-3358 User’s Manual Driver Setup CHAPTERChapter 3.1 Overview3.2 USB driver Figure 3.1 Right Click My Computer and click Properties 3.3 CMM Chassis Management Module Driver3.3.1 Windows 2K Driver Figure 3.2 Tab Hardware and click Hardware WizardFigure 3.3 click Next in Hardware Wizard Figure 3.4 click Add/Troubleshoot a deviceMIC-3358 User’s Manual Figure 3.5 select Add a new device in Device windows Figure 3.6 click No, I want to select the hardware from a listChapter3 Figure 3.7 Select Other devices in Hardware types windows Figure 3.8 Tab Have Disk in right bottomMIC-3358 User’s Manual Figure 3.9 Browse proper driver in CD ROM device Figure 3.10 click ok in the Wizard windowsChapter3 Figure 3.12 click yes in Creating a Forced Configuration windows Figure 3.11 click ok in Add New Hardware Wizard Properties windowsMIC-3358 User’s Manual Figure 3.13 click Next in Add/Remove Hardware Wizard windows Figure 3.14 Tab Finish in Add/Remove Hardware Wizard windowsChapter3 Figure 3.15 click Yes to restart your computer Figure 3.16 Go to Device Manager to see available A-IPM driversMIC-3358 User’s Manual Figure 3.18 Tab Hardware and click Add Hardware Wizard 3.3.2 Windows XP DriverFigure 3.17 Right click My Computer to select Properties Chapter3Figure 3.19 Click Next in the windows Figure 3.20 Click Yes , I have already connected the hardwareMIC-3358 User’s Manual window AdvancedChapter3 Figure 3.23 Select Show all devices in Common hardware types windows Figure 3.24 tab Have DiskMIC-3358 User’s Manual Figure 3.25 Select proper driver in CD-ROM Figure 3.26 tab A-IPM driver and click Have DiskChapter3 Figure 3.27 Click Next Figure 3.28 Click Finish MIC-3358 User’s ManualFigure 3.29 Go to My computer to see A-IPM drivers Chapter3MIC-3358 User’s Manual Award BIOS Setup CHAPTER4.1.1 Entering Setup Chapter 4 Award BIOS Setup4.1 AWARD BIOS Setup Figure 4.1 Setup program initial screenFigure 4.2 Standard CMOS setup screen 4.1.2 Standard CMOS Setup4.1.3 Advance BIOS Features Setup Primary Master/Primary Slave/Secondary Master/Secondary SlaveFigure 4.3 Advance BIOS features setup screen Virus Warning Quick Power On Self TestNote The internal cache is built in the processor Boot Up NumLock Status First/Second/Third Boot Device and Boot Other DeviceBoot Up Floppy Seek Swap Floppy DriveAPIC Mode Advanced Programmable Interrupt Controller Typematic Rate SettingTypematic Delay Msec Typematic Rate Chars/SecDRAM RAS# to CAS# Delay 4.1.4 Advance Chipset Features SetupActive to Precharge Delay Small logo EPA showVideo BIOS Cacheable DRAM Data Integrity ModeSystem BIOS Cacheable DRAM RAS# Precharge4.1.5 Integrated Peripherals Delayed TransactionFigure 4.5 Integrated Peripherals setup screen Chapter4IDE Primary/Secondary Master/Slave UDMA On-Chip Primary/Secondary PCI IDEIDE Primary/Secondary Master/Slave PIO USB ControllerLAN 2 Connector SMBus ConnectorLAN 1 Connector IDE HDD Block ModeECP Mode Use DMA 4.1.6 Power Management SetupParallel Port Mode Figure 4.6 Power management setup screenReset Configuration Data 4.1.7 PNP/PCI Configuration SetupFigure 4.7 PNP/PCI configuration screen ACPI Function4.1.8 PC Health Status 4.1.9 Load Optimized DefaultsFigure 4.8 PC Health setup screen IRQ ResourcesLoad Optimized Defaults Y/N ? N 4.1.10 Set Password4.1.11 Save & Exit Setup 4.1.12 Exit Without SavingMIC-3358 User’s Manual Programming the Watchdog Timer Appendix70 X=INP &H043 REM, Disable the watchdog timer A.1 Programming the Watchdog Timer10 REM Watchdog timer example program Appendix A2090 RETURN 2000 REM Subroutine #2, your application task1070 RETURN ChapterAMIC-3369 User’s Manual Pin Assignments AppendixAppendix B Pin Assignments B.1 J1 ConnectorTable B.1 J1 connector MIC-3358 User’s ManualB.2 J2 Connector Table B.2 J2 connectorChapterB B.3 J3 Connector Table B.3 J3 connectorMIC-3358 User’s Manual B.4 J5 Connector Table B.4 J5 connectorChapterB B.5 System I/O Ports Table B.5 System I/O portsMIC-3358 User’s Manual Table B.6 Interrupt assignments B.6 Interrupt AssignmentsB.7 1st MB Memory Map Table B.7 1st MB memory mapMIC-3358 User’s Manual