Here, the 2-port 10/100 Downlink bridges the two 100 Mbps hubs to the two 10 Mbps hubs.

The benefits of using the Downlink are its low cost and simplicity. Just plug the hubs into the Downlink; it takes care of the rest.

Bridging with the Express 10/100 Downlink

The Express 10/100 Downlink has two ports that operate at either 10 or 100 Mbps. Each port automatically senses the speed of the attached device. All you need to do is set the speed of the hubs. No configuration of your network operating system is needed.

Intel Express 10/100 Downlink

Intel Express 10/100 Downlink

Express 10/100 Stackable Hubs

Intel Express

10/100 Stackable Hub

Intel Express

10/100 Stackable Hub

Intel Express

10/100 Stackable Hub

Intel Express

10/100 Stackable Hub

Hub 1 (100 Mbps)

Hub 2 (100 Mbps)

Hub 3 (10 Mbps)

Hub 4 (10 Mbps)

Category 5 TPE (100m max.)

Category 3, 4, or 5 TPE (100m max.)

100 Mbps-only environment

In the 100-Mbps only environment, you can only connect hubs using an Intel Cascade Cable. You must also use CAT 5 TPE cabling to connect devices (switches, workstations, servers, and so on). The distance between a port and an attached device can’t exceed

100 meters.

100Mbps

shared among all hubs in stack

Intel Express

10/100 Stackable Hub

Change hub speed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10BASE-T

Collision

Power

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100BASE-TX

Managed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Status

 

1

2

3

4

5

6

7

8

 

9

10

11

12

 

 

 

 

Intel Express

10/100 Stackable Hub

Change hub speed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10BASE-T

Collision

 

Power

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100BASE-TX

Managed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Status

 

 

 

1

2

3

4

5

6

7

8

 

9

10

11

12

13

14

15

16

 

17

18

19

20

21

22

23

24

 

 

Intel Express

10/100 Stackable Hub

Change hub speed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10BASE-T

Collision

 

Power

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100BASE-TX

Managed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Status

 

 

 

1

2

3

4

5

6

7

8

 

9

10

11

12

13

14

15

16

 

17

18

19

20

21

22

23

24

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If you intend to install an optional Management Module in a 12-port hub, place the hub at eye level. This makes it easier to read the module’s LCD panel.

Category 5 TPE (100m max.)

7

Page 9
Image 9
Intel PCLA2152B manual Mbps-only environment, Bridging with the Express 10/100 Downlink