Intel TE430VX - page 49

Motherboard BIOS and Setup Utility

49

3.12.4.6 IDE Translation Mode

Specifies the IDE translation mode. The options are Standard CHS (standard cylinder head sector

−less than 1024 cylinders), Logical Block, Extended CHS (extended cylinder head sector−greater

than 1024 cylinders), and Auto Detected (BIOS detects IDE drive support for LBA). The default is

Auto Detected.

CAUTION

Do not change this from the option selected when the hard drive was formatted. Changing the

option can result in corrupted data.

3.12.4.7 Multiple Sector Setting

Sets the number of sectors transferred by an IDE drive per interrupt generated. The options are

Disabled, 4 Sectors/Block, 8 Sectors/Block, or Auto Detected. The default is Auto Detected.

Check the specifications for your hard disk drive to determine which setting provides optimum

performance for your drive.

3.12.4.8 Fast Programmed I/O Modes

Sets how fast transfers on the IDE interface occur. The options are Disabled or Auto Detected.

The default is Auto Detected. If set to Disabled, transfers occur at a less than optimized speed. If

set to Auto Detected, transfers occur at the drive's maximum speed.

3.12.5 Boot Options Subscreen

This section describes the options available on the Boot Options subscreen.

3.12.5.1 First, Second, Third, Fourth Boot Device

Sets which drives the system checks to find an operating system to boot from. The following

options are available:

First Boot Device: Select Disabled, Floppy, Hard Disk, CD-ROM, Network.

Second, Third, Fourth Device: Select Disabled, Floppy, Hard Disk, Network.

3.12.5.2 System Cache

Enables or disables both the primary and the secondary cache memory. The options are Enabled or

Disabled. The default is Enabled.

3.12.5.3 Boot Speed

Sets the system’s boot speed. The options are Deturbo and Turbo. The default is Turbo. If Turbo

is selected, boot-up occurs at full speed. If Deturbo is selected, the board operates at a slower

speed.

Contents

Main Revision History Table of Contents 1 Motherboard Description 2 Motherboard Resources 3 Motherboard BIOS and Setup Utility 4 Error Messages and Beep Codes Page 1 Motherboard Description 1.1 Overview Tigereye board diagram 1.2 Motherboard Manufacturing Options 1.3 Form Factor 1.4 Microprocessor 1.4.1 Microprocessor Upgrade 1.5 Memory 1.5.1 System Memory 1.5.1.1 EDO DRAM 1.6 Chipset 1.6.1 82430VX System Controller (TVX) 1.6.2 82430VX Data Path (TDX) 1.6.3 PCI ISA/IDE Xcelerator (PIIX3) 1.6.4 IDE SUPPORT 1.7 Ultra I/O Interface Controller (SMC FDC37C93FR) 1.7.1 Floppy controller 1.7.2 Keyboard and mouse interface 1.7.3 Real time clock, CMOS RAM and battery 1.7.4 IrDA (infra-red) support 1.8 Graphics Subsystem (S3 Trio64V+) 1.8.1 Resolutions supported 1.8.2 Graphics Drivers and Utilities 1.9 Audio Subsystem (Creative Labs Vibra 16C) 1.9.1 Vibra 16C resource map 1.9.2 Audio Drivers 1.10 Motherboard Connectors Figure 3 shows the connectors on the motherboard. Pin call outs and signal names follow Figure 3. Figure 3. Motherboard Connector Locations 1.10.1 CD-ROM Connector - J2F2 1.10.2 Wave Table Connector - J2F3 1.10.3 Telephony Connector - J2F1 1.10.4 Power Connector - J7M2 1.10.5 Floppy Drive Connector - J10H1 1.10.6 IDE Connectors - J9H1, J9H2 IDE Connectors - J9H1, J9H2 (continued) 1.10.7 Front Panel I/O Connectors - J9E2 1.10.8 ISA Connectors- J1A1, J1A2, J1B1 ISA Connectors (continued) 1.10.9 PCI Connectors - J2C1, J2D1, J2E1, J2E2 1.10.10 Power Supply Connectors 1.10.11 Front panel Connectors 1.10.11.1 Speaker 1.10.11.2 Reset 1.10.11.3 Sleep or Power LED 1.10.11.4 HD LED 1.10.11.5 Infra-Red (IrDA) connector 1.10.11.6 Sleep / resume 1.10.11.7 Remote ON/OFF and Soft Power Support 1.10.12 Back Panel Connectors Motherboard Description 27 Figure 5. I/O Connections 1.10.13 Add-in Board Expansion Connectors 1.11 Jumper Settings J9C1 A B C D J7A1 J6M1 1.11.1 CPU Configuration (J9C1-C, D) 1.11.2 Clear CMOS (J9C1-A, Pins 4,5,6) 1.11.3 Password clear (J9C1-A, Pins 1,2,3) 1.11.4 CMOS Setup Access (J9C1-B, Pins 1,2,3) 1.11.5 CPU Voltage (J6M1) 1.12 Reliability 1.13 Environmental 1.14 Power Consumption 1.15 Regulatory Compliance Page 1.15.3.3 Canadian Compliance 1.15.4 Installation Requirements 1.15.4.1 Follow Installation Instructions 1.15.4.2 Assure Host System Compatibility 1.15.4.3 Use Only In Intended Applications 1.15.4.4 Assure Host System & Accessory Certifications Europe U.S. Canada 1.15.4.5 Installation Precautions 1.15.4.6 Battery Marking 1.15.4.7 Overload Protection: Page 2 Motherboard Resources 2.1 Memory Map Table 6. Memory Map 2.2 I/O Map Table 7. I/O Map Table 7. I/O Map (continued) 2.3 Soft-Off Control The motherboard design supports Soft-off control via the SMM code in the BIOS 2.4 PCI Configuration Space Map Table 8. PCI Configuration Space Map 2.5 DMA Channels 2.6 Interrupts Table 10. Interrupts 3 Motherboard BIOS and Setup Utility 3.1 Introduction 3.2 BIOS Flash Memory Organization 3.3 BIOS Upgrades 3.4 PCI IDE Support 3.5 PCI Auto-configuration 3.6 ISA Plug and Play 3.7 Advanced Power Management 3.8 Language Support 3.9 Boot Options 3.10 Flash LOGO Area 3.11 Setup Enable Jumper 3.12 BIOS Setup Program 3.12.1 Overview of the Setup Menu Screens 3.12.2 Main BIOS Setup Screen 3.12.2.1 System Date 3.12.2.2 System Time 3.12.2.3 Floppy Options 3.12.2.4 Primary Master Page Page Page Page Page Page Page Page 3.12.11 Security Screen 3.12.11.1 Administrative and User Access Modes Page Page Page 4 Error Messages and Beep Codes 4.1 BIOS Beep Codes 4.2 PCI Configuration Error Messages The following PCI messages are displayed as a group with bus, device and function information. The following messages chain together to give a message such as: 4.3 BIOS Error Messages BIOS Error Messages (continued) 4.4 ISA NMI Messages