Intermec 7421 Printer Specifications

A-3

Printer Specifications

This section describes the specifications for the 7421 printer.

Character Sets

•US ASCII •Norwegian/Danish •French

•UK ASCII •Swedish/Finnish •Swiss

•German •Italian •Spanish

•8-bit ASCII •Code Page 850

Communications

•Asynchronous RS-232C, IEEE 1284 Bi-directional Parallel

•Serial ASCII code

•Hardware (Ready/Busy) Flow Control

•XON/XOFF Protocol

•Intermec Standard Block Protocol

•Baud Rates: 1200, 2400, 4800, 9600, 19200

Dimensions (no options installed)

Height 7 inches (17.8 cm)

Width 8 inches (20.3 cm)

Length 10 inches (25.4 cm)

Weight 4.5 pounds (2.0 kg)

Electrical Requirements, External Power Supply

Input Voltage ~100 to 240V

Frequency 50-60 Hz

Current 2A maximum

Electrical Requirements, Printer

Input Voltage xw19-21V

Current 2,5A

Environment

Operating 40°F to 104°F (5°C to 40°C)

Humidity 10% to 90% noncondensing

Contents

Main Page Contents Operating the Printer Configuring the Printer Maintaining the Printer Troubleshooting 3 4 A Page Page vii Before You Begin Warranty Information Safety Summary viii Warnings, Cautions, and Notes ix About This Manual What You Will Find in This Manual This table summarizes the information in each chapter of this manual: For Information On Refer To x Terms Other Intermec Manuals Page Page 1-3 . Getting to Know Your Printer Front View 1-4 Back View 1-5 Learning How to Operate the Printer Understanding the Power Light 1-6 Using the Feed/Pause Button 1-7 Loading Media Into the Printer Using the Peel-Off Option Page Page 1-10 Page Page Page Page 1-15 1-16 Loading Fanfold Media Page Page Page 1-20 Inserting the Optional Memory Card Page Page 2-3 Configuring the Printer Setting the Media Sensitivity Number 2-4 Finding Your Media Sensitivity Number 2-5 Setting the MSN for Intermec Media and Ribbon 2-6 Setting the MSN for Other Media and Ribbon Direct Thermal Media Sensitivity Settings 2-7 Thermal Transfer Media and Ribbon Sensitivity Settings 2-8 Adjusting the Print Darkness Co de 39 2-9 Adjusting the Label Gap Sensor 2-10 Communicating With the Printer Printing a Test Label 2-11 2-12 Using the Printhead Loading Modes 2-13 Page Page Page Maintenance Schedule 3-4 Locating the Printer Parts You Need to Maintain 3-5 Tools for Cleaning the Printer 3-6 Cleaning the Printhead 3-7 Cleaning the Printhead Cleaning the Printer Covers 3-8 Cleaning the Drive Roller and Peel-Off Bar Page 3-10 Cleaning the Label Sensors Page Page Page Page 4-3 Troubleshooting Checklist 4-4 Printer Operation Problems 4-5 Print Quality Problems Symptom Possible Causes Solution 4-6 Communication Problems Using Data Line Print Mode 4-7 Preventing Data Loss 4-8 Resetting the Printer to Factory Defaults Page Page Printer Specifications A-4 Fonts and Graphics Media Specifications Memory Printhead Printing Method Printer Options A-6 Bar Code Symbologies Supported Page Page B-3 About Communications Serial Communication Protocols Intermec Printer Standard Protocol B-4 B-5 XON/XOFF Protocol B-6 Hardware Protocol User-Defined Protocol B-7 B-8 Communications Boundaries RS-232 Serial Interface B-9 Pin Name Operation B-10 RS-232 Cable for 9-pin to 9-pin (Part No. 590123) RS-232 Null Modem Cable for PC for 25-pin to 9-pin Page Page International Character Sets Advanced Character Table C-4 86XX Character Table C-5 IBM Translation Character Table C-6 Code Page 850 Character Table #$%&'() " ! Extended Character Sets C-8 7421U.047 C-9 Characters in Font c23 OCR A 7421U.047 C-10 Characters in Font c24 OCR B Size 2 Page Page I-3 A B C I-4 D E F G H M O P I-6 Q R S T