Intermec PF4I, PX4I, PF2i, PF4i Compact Industrial, PM4i, PX6i Examples

46 EasyLAN Wireless Interface Kit Installation Instructions

Chapter 5 — Setup in IPL

To reinstall the default root CA certiﬁcate, install /rom/intermec.cer, or

remove the /c/ADMIN/root.cer ﬁle.

Examples

<STX><SI>ws,EAP_TYPE,TTLS|LEAP|PEAP|OFF<ETX>

Sets preferred EAP type.

<STX><SI>ws,.EAP_USER,Admin01<ETX>

Sets logon user name to “Admin01”.

<STX><SI>ws,EAP_PASS,InfoTech<ETX>

Sets logon password to “InfoTech”.

Note: It is not possible for any user to read the EAP_PASS

value.

<STX><SI>ws,TTLS_USER,Manufacturing<ETX>

Sets TTLS outer name to “Manufacturing”.

<STX><SI>ws,INNER_AUTH,PAP|MSCHAPv2|EAP/

MSCHAPv2|EAP/MD5|EAP/GTC<ETX>

Sets inner authentication type (TTLS/PEAP only).

<STX><SI>ws,CA_CERT,/tmp/mycacert.cer<ETX>

Installs overriding CA certiﬁcate (TTLS/PEAP only).

<STX><SI>ws,CA_CERT,/tmp/mycacert.pfx@

verysecret<ETX>

Installs overriding CA certiﬁcate with pass phrase “verysecret”(TTLS/

PEAP only). is method can be used only when the certiﬁcate has

already been transferred to the printer (for example, via FTP or an

installed Compact Flash card).

<STX><SI>ws,DOWNLOAD_CA<ETX>

Start receiving the CA certiﬁcate via Zmodem and install it.

<STX><SI>ws,DOWNLOAD_CA,verysecret<ETX>

Start receiving the CA certiﬁcate via Zmodem and install it, using the

pass phrase “verysecret”.

<STX><SI>ws,.SERVER_CN1,Printer33<ETX>

Sets common name 1 to “Printer33” (TTLS/PEAP only).

<STX><SI>ws,.SERVER_CN2,Printer34<ETX>

Sets common name 2 to “Printer34” (TTLS/PEAP only).

Contents

Main Page Page Page Contents 1 2 3 4 5 6 Page Before You Begin Safety Information Global Services and Support Warranty Information Web Support Telephone Support Who Should Read This Manual Related Documents Page Page About These Instructions Printer Firmware Installation Kit 2 Step-by-Step Instructions EasyCoder PF2/4i Printers Page Page Page EasyCoder PM4i Printers Page Page EasyCoder PX4/6i Printers Page Page Page Page Setting up Network Parameters Establishing Serial Communications Setup with CompactFlash (Fingerprint only) User and Password 4 Setting Up Wireless Communications General Display Current User Changing User Changing Passwords Active Page SSID (Network Name) WEP 802.11 Authentication WPA Roaming Bias 802.1x Supported EAP Types 802.1x Settings Using Certicates Examples Reading Other Wireless Connection Variables Active Channel Access Point Information Signal Strength Speed Region (a.k.a. Regulatory Domain) Reading Wireless Connection Setup Setting Up Network Parameters New Line IP Selection Method IP Address Subnet Mask Finishing the Setup Page 5 Setting Up Wireless Communications General Display Current User Changing User Changing Passwords Active SSID (Network Name) WEP 802.11 Authentication WPA Roaming Bias 802.1x Supported EAP Types 802.1x Settings Using Certicates Examples Reading Other Wireless Connection Variables Active Channel Access Point Information Signal Strength Speed Region (a.k.a. Regulatory Domain) Finishing the Wireless Setup Setting Up Network Parameters Setting the IP Selection Method Read-only Read-only Read-only Read-only Read-only These menus will only be displayed when an optional EasyLAN interface board is installed. EasyLAN Wireless Interface Kit Installation Instructions 51 Reading the IP Address 1 After having selected the method for assigning the IP address, the display shows: NETWORK: IP ADDRESS Example of the network setup when an automatic IP selection method is used. IP ADDRESS: 192.168.1.79 Reading the Netmask, Default Router, and Name Server Using ARPnPING to set an IP Address (Windows) Page Setting Network Parameters in Manual Mode Page Page Page Page Page *1-960610-04*