Manuals / Intermec / Computer Equipment / Printer

Intermec PF8D, PF8T manual Plain Continuous Stock

Models: PF8D PF8T

1 68

Download 68 pages 11.44 Kb

Page 67

Image 67

Appendix B — Media Specifications

Plain Continuous Stock

The PF8 printers can use continuous stock without any detection slots or black marks. The printer must be set for continuous stock by using the ESim Q command (see ESim Programmer’s Reference Manual).

The length of each copy is decided by the size of the print image and any additional media feed is decided by the Q command. Continuous stock cannot be used in the Auto-Sensing mode.

Tag or strip width (a)

Maximum: 116.0 mm (4.57 in)

Minimum: 25.0 mm (1.00 in)

CONTINUOUS STRIP

54	PF8d/PF8t Printer User’s Guide

Page 67

Image 67

Intermec PF8D, PF8T manual Plain Continuous Stock

Contents

PF8d/PF8t Printers User’s GuidePage Page PF8d/Pf8t Printers User’s GuideIntermec Technologies Corporation Worldwide Headquarters PF8d/PF8t Printer User’s Guide Document ChangeVersion Date Description of ChangePF8d/PF8t Printer User’s Guide Contents ContentsPF8d/PF8t Printers User’s Guide Contents 3 Troubleshooting and Maintaining the PrinterB Media Specifications PF8d/PF8t Printers User’s Guide ContentsBefore You Begin Safety InformationDescription Global Services and SupportSupport Warranty ServicesPatent Information Who Should Read This ManualPF8d/PF8t Printers User’s Guide 1 Using the PF8 PrintersIntroducing the PF8 Printers Features of the PF8 Printers Understanding the LED IndicatorsIntroducing the PF8 Printers Front Controls and Indicators Features of the PF8 PrintersChapter 1 - Using the PF8 Printers Media CompartmentPF8d Media Compartment PF8t Media Compartment Chapter 1 - Using the PF8 Printersadjustment PF8d/PF8t Printers User’s GuidePF8d Wall-Mount Holes Other Features and ConnectionsChapter 1 - Using the PF8 Printers PF8d and PF8t Rear View Connections and ControlsLED Status Indicators Understanding the LED IndicatorsPF8d/PF8t Printers User’s Guide Chapter 1 - Using the PF8 PrintersUnderstanding Auto-Sensing Mode Creating and Printing Labels 2 Installing the PrinterConnecting the Printer to Your Network Turning on the Printer Installing the Compact Flash PF8t OnlyConnecting the Printer Through the Parallel Port Connecting the Printer to Your NetworkConnecting the Printer Through the USB Interface Connecting the Printer Through the Serial PortChapter 2 - Installing the Printer 3 Click the Install InterDriver linkPF8d/PF8t Printers User’s Guide PF8d/PF8t Printers User’s Guide Chapter 2 - Installing the PrinterPage PF8d/PF8t Printers User’s Guide Chapter 2 - Installing the PrinterTo power the printer Turning On the PrinterDanger of personal injury if the printer and power supply To install the compact flash card Installing the Compact Flash PF8t OnlyTo use Auto-Sensing mode Understanding Auto-Sensing ModeLoading Media Creating and Printing LabelsIntroduction Peel-Off Loading Media for Tear-off OperationTear-Off Cut-OffNote The PF8d spindle lifts up, but remains attached to the printer while the PF8t spindle lifts completely out of the spindle compartment PF8d/PF8t Printers User’s Guide 5 Adjust the label guide to fit the media you are usingChapter 2 - Installing the Printer 4 Put the label between the label guides and pull it forwardTo load peel-off media Loading Media for Peel-Off OperationLoading an Media from an External Supply Loading Media for Cut-Off OperationTo load cut-off media To load a fresh ribbon roll Loading Thermal Transfer Ribbon PF8t Only3 Lift the print carriage halfway up while keeping the top cover fully opened. Insert a new ribbon roll onto the ribbon supply shaft To remove a partially used ribbon PF8d/PF8t Printers User’s Guide Chapter 2 - Installing the PrinterPF8d/PF8t Printers User’s Guide Chapter 2 - Installing the PrinterAdjusting the Print Alignment Adjusting the Label Taken Sensor 3 Troubleshooting and Maintaining the PrinterTroubleshooting Upgrading the Firmware Cleaning the Case Cleaning the Printhead Adjusting the Thermal Printhead PressureSolution or Reason TroubleshootingChapter 3 - Troubleshooting and Maintaining the Printer ProblemTo clean the printhead Cleaning the CaseCleaning the Printhead Upgrading the FirmwareTo adjust thermal printhead pressure Adjusting the Thermal Printhead Pressure PF8t onlyAdjusting the Label Taken Sensor Adjusting the Printhead Alignment“Understanding Auto-Sensing Mode” on page Adjusting the Label Gap SensorPF8d/PF8t Printers User’s Guide A SpecificationsPF8d Specifications Fonts Download Serial Interface Connections Communication InterfacesUSB Interface Function Parallel InterfaceHandshake DSTB connects to the printer, BUSY connects to the host Interface cable Parallel cable compatible with PCInternal Interface PF8t SpecificationsSensor Detection Certification PowerPrinter Dimensions EnvironmentFunction Appendix A - SpecificationsUSB Interface Parallel InterfaceCutter Kit AccessoriesInternal Interface Appendix A - Specifications Stripper ModulePF8d/PF8t Printers User’s Guide PF8d/PF8t Printers User’s Guide Appendix A - SpecificationsPF8d/PF8t Printer User’s Guide B Media SpecificationsExamples of Economy Quality Media Direct Thermal MediaThermal Transfer Media Examples of Premium Quality MediaTTR High Gloss Polyester Examples of Coated PapersExamples of Polyethylene Plastics Examples of PolyestersHigh Resistance HR/TMX3201/TMX3202 Transfer RibbonsGeneral Purpose GP/TMX1500 High Performance HP/TMX2200PF8d/PF8t Printer User’s Guide LabelsChapter B - Media Specifications a b cDetection slot width c Tags and Strip with SlotsTag or strip width a Tag length bDetection slot/Black mark width c Tags and Strip with Black MarksTag or strip width a Tag length bPlain Continuous Stock PF8d/PF8t Printer User’s Guide 934-011-002