InterMetro Ind C199, FL199 II. Operating Instructions, Features ALL Models, Reversible Doors

B. FEATURES — ALL MODELS

In order to utilize your new cabinet to its full potential, take a minute to identify the following features which have been provided for your convenience.

•The module has been placed at the base of the cabinet for easy accessibility and efficient operation.

•Clearly-marked control panel for easy viewing

and allowing climate adjustments without opening the door(s).

•Removable water pan (C199) or water bottle (FL199).

•Rear pan stop.

•Field reversible insulated and gasketed door(s).

•Easy pull adjustable magnetic door latch.

•Cord keeper at rear of cabinet which folds flat to prevent damage to surrounding walls.

•All components — door(s), module, chimney, slide racks — removable to permit thorough, obstruction-free cleaning.

II.OPERATING INSTRUCTIONS

A.REVERSIBLE DOOR(S)

The door(s) on your cabinet can be reversed to accommodate a right- or left-hand opening. The cabinet has been shipped with the hinges mounted on the right-hand side. To reverse, follow the instructions listed below (read completely before starting procedure):

1.With the doors in the closed position remove the hinge pin by driving it out using a hammer and a drive pin or small diameter screwdriver.

2.Once the pins are removed grasp the door firmly and pull the latch lever, this will release the door. Repeat the process for double door units. Set the door(s) aside being careful not to damage the gaskets.

3.Remove the screws from the left side of the cabinet and set aside. Then remove the cabinet mounted part of the hinge and remount to the left side of the cabinet. Put the screws removed from the left side of the cabinet, into the remaining holes on the right side of the cabinet. Tighten all screws before proceeding.

4.Relocate the latch plate(s) from the left side to the right by removing the two mounting screws. Tighten all screws before proceeding.

5.On single door units rotate the door 180 degrees and align the door mounted hinge part with the cabinet mounted hinge part and tap the hinge pin into place so top of pin is flush with top of the cabinet mounted hinge part. Invert the door latch by removing black plastic screw covers and remove the screws holding the latch in place.

6.On double door units rotate the top-door 180 degrees and mount in the position of the lower door. Rotate what was the bottom-door 180

degrees and mount in the position of the top door. Align the door mounted hinge part with the cabinet mounted hinge part and tap the hinge pin into place so top of pin is flush with top of the cabinet mounted hinge part.

7.Relocate the label on the door(s). Be sure that there are no open screw holes on the front of the cabinet.

B.SLIDE RACK ASSEMBLIES

All models of slide racks are removable for thorough cleaning.

On the inside of each cabinet are a series of rack hangers. These hangers have two slots for either an inboard or outboard rack position. To remove the slide rack, grasp and move upward until the pins are free of the hanger slots. To install the racks, locate the pins over the hangers and lower until locked into the slots.

NOTE: For an inboard rack position, use the slots farthest away from the wall of the cabinet. For an outboard rack position, use the slots closest to the wall of the cabinet.

C4SC/-T/-H — Model 4 (3" Slide Spacing fixed) The Slide Rack consists of two (2) pair of slides and the C4SC-T and C4SC-H consist of (1) pair of slides. The pairs can be placed in the inboard or outboard position. The C4SC can have one pair in the inboard position and one pair in the outboard position. All pans are to be bottom loaded regardless of rack position. The following pans may be used:

Inboard Hanger Position (18" width)

Pan Size	C4SC	C4SC-T C4SC-H
18"x26"x25/8"	17 pans	13 pans	8 pans
14"x18"x25/8"	17 pans	13 pans	8 pans

Max. pan size: 18"x27"x25/8"

Min. pan size: 17"

Outboard Hanger Position (20" width)

C4SC	C4SC-T C4SC-H
17 pans	13 pans	8 pans
14 pans	13 pans	8 pans
34 pans	26 pans	16 pans
28 pans	26 pans	16 pans

Max. pan size: 20"x27"x25/8"

Min. pan size: 19"

C8SN/-T/-H — Model 8 (11/2" Spacing-fixed)

The Model 8 Slide Rack can only be installed in the inboard hanger position. All pans are to be lip loaded. The following pans may be used:

	Model 8 Slide Rack
C8SN	C8SN-T	C8SN-H	Pan Size
34 pans	28 pans	17 pans	18"x26"x13/8"

2