ADJUSTINGAND OPERATING

LEVELING THE MOWER

A properly leveled mower is one where the blades are cutting parallel to the ground. Should level adjustment be necessary due to tire variation orwear,

proceed asfollows:

CAUTION! To avoid possible injury, stop the engine, disconnect the high tension wire to the spark plug, and lock

the brake prior to leveling the mower.

Leveling the Mower From Front to Rear

Drive the lawn tractor onto a hard flat surface.

NOTE: Substitute belts may not be satisfactory. Use only specified replacements. See your Interna- tional Harvester dealer.

Refer to the instructions for attaching and detach- ing the mower.

Both belt guides must be removed from the mowerhousin in order to replace the belt.

After replacing the belt and two belt guides, check and make sure the belt guides do not rub against the mower pulleys.

the ignition off and disconnect the high

tension wire to the spark plug. Lock the tractorbrake.NOTE: When installing a new belt, make certain that the belt runs correctly between the pulleysand

the belt guides.

Measure the distance from the ground to the blades

 

(blades parallel to centerline of tractor) front and

 

rear in typical cutting height. Adjust

the clevis onthe

 

end of the mower linkage rod

either

up ordown,CRANKSHAFT

MAIN DRIVE AND HYDRO-

depending on which measures high.

STATIC FINAL

DRIVE BELTS

Leveling the Mower From Side to Side

left lift link is adjustable should the mower require side to side adjustment. Turn the adjusting bolt up or down depending on which side measures too high.

MOWER DRIVE V-BELT

A CAUTION! To avoid an accident or possible injury, always stop the engine, disconnect the high tension wire to the spark plug, and lock the brake before doing any

work on the machine.

The mower drive belt requires no adjusting, as proper belt tension is maintained by the spring loaded mower drive belt idler.

When the belt has worn or stretched to a point where slippage occurs, a new belt should be installed.

The drive belts are set at the factory and require no adjustment. When the belts have worn or stretched to a point where slippage occurs in forward or reverse, new belts should be installed.

Set the mower clutch lever in the "OFF" position, set the speed control lever in "NEUTRAL", and

lock the parking brake.

Disconnect high tension wire to the spark plug.

Detach the mower. Refer to Attaching and De- taching instructions.

Disconnect the spring loaded mower drive belt idler from the mower clutch arm in order to reach the crankshaft drive belt idler and also in order to remove the hydrostatic final drive belt.

To disconnect the spring, pull the mower drive idler to the right of the tractor and insert a coin (a Quarter is recommended) between two coils of the spring. See page 13.

Page 13
Image 13
International Home Products Cadet 80 manual Main Drive and Hydro, Static Final Drive Belts

Cadet 80 specifications

The International Home Products Cadet 80 is a standout model in the realm of energy-efficient heating solutions. Designed with the modern consumer in mind, this electric wall heater combines functionality, aesthetics, and reliability. Its sleek design allows it to fit seamlessly into any home decor, making it a versatile addition to varied spaces, whether in residential or commercial settings.

One of the primary features of the Cadet 80 is its compact size, which enables it to be installed in tight spaces without compromising performance. The heater's slim profile allows for discreet placement, ensuring that it complements rather than detracts from the room's appearance. With a capacity of 800 watts, this model is ideal for heating small to medium-sized rooms, delivering consistent warmth during colder months.

The Cadet 80 is equipped with advanced technologies that enhance user experience and efficiency. It incorporates an easy-to-use adjustable thermostat that allows homeowners to set their desired temperature with precision. This feature not only maximizes comfort but also contributes to energy savings, as the system can automatically adjust its output based on the room’s heating needs.

Another hallmark of the Cadet 80 is its safety features. The heater includes a built-in overheat protection mechanism, providing peace of mind for users. This feature automatically shuts off the unit if it becomes too hot, preventing potential hazards and ensuring safe operation. Furthermore, the durable, heavy-duty construction of the Cadet 80 ensures longevity, withstanding the rigors of daily use.

Additionally, the easy installation process of the Cadet 80 is worth noting. The unit can be hardwired directly into the electrical system, making it suitable for permanent installation in various settings. This eliminates the need for cumbersome cords and allows for a cleaner aesthetic.

In summary, the International Home Products Cadet 80 electric wall heater stands out for its compact design, efficient heating capacity, user-friendly controls, and emphasis on safety. For those seeking a reliable and stylish heating solution for small to medium rooms, the Cadet 80 presents an excellent choice, merging modern technology with practical features that enhance comfort and convenience.