CARBURETOR ADJUSTMENTS

 

1-Needle

valve

 

 

 

 

 

2-ldle

valve

 

 

 

 

 

3-ldle

speed adjusting screw

 

 

A

CAUTION!

 

During

operation

 

do not

run

 

the engine

in

confined

areas

such

as

storage building any longer than is necessary for immediate moving of the machine

outside into the air. Exhaust gases are toxic. Opening doors and windows may not provide adequate ventilation.

The carburetor is adjusted at the factory. Do not make adjustments unless absolutely necessary. Fac- tory settings are correct for normal operating conditions. I f adjustments are necessary, proceed as follows:

15

The

Start the engine and allow it to warm up at 3000 RPM. Turn needle valve in until engine misses (lean mixture) then turn it out past smooth operating point until engine runs unevenly (rich mixture).

Turn needle valve to the mid-point between rich and lean so engine runs smoothly. Hold throttle at idle position and set idle speed, adjusting screw until engine idle speed is 1800 RPM. Hold throttle at idle position and turn idle valve in (lean) and out (rich) until engine idles smoothly. If necessary, correct idle speed. Release the throttle -engine should accelerate without hesitation or sputtering. If engine does not accelerate properly, the car- buretor should be readjusted, usually to a slightly richer mixture of needle valve.

Recommended Fuel

This engine is designed to operate on leaded gasoline with a 93 minimum octane rating or on unleaded or low lead gasoline with a 91 minimum octane rating (Research Method).

use of unleaded gasoline will lengthen spark plug and valve life, maintain engine performance longer, and reduce rust and corrosion of enginewhile

stored.

CAUTION! Handle gasoline with care, as it is highly flammable. A. Use approved

gasoline container. B. Never remove the fuel tank cap or fill tank when the engine is

running, is hot, or indoors. Also, do not smoke when working around flammable fuel. Wipe up spilled gasoline. C. Replace fuel tank cap securely.

battery is located under the hood and in back of the fuel tank.

A charging circuit built into the engine provides a charging circuit output from 2 amperes at 2400 APM to 3 amperes at 3600 APM and uses lessthan

.2 horsepower.

Check the battery level at least once a month.

Keeping the battery fully charged not only adds to

its life but makes it available for instant use whenneede

Page 16 Page 18
Page 17
Image 17
International Home Products Cadet 80 manual Carburetor Adjustments
Page 16 Page 18

Cadet 80 specifications

The International Home Products Cadet 80 is a standout model in the realm of energy-efficient heating solutions. Designed with the modern consumer in mind, this electric wall heater combines functionality, aesthetics, and reliability. Its sleek design allows it to fit seamlessly into any home decor, making it a versatile addition to varied spaces, whether in residential or commercial settings.

One of the primary features of the Cadet 80 is its compact size, which enables it to be installed in tight spaces without compromising performance. The heater's slim profile allows for discreet placement, ensuring that it complements rather than detracts from the room's appearance. With a capacity of 800 watts, this model is ideal for heating small to medium-sized rooms, delivering consistent warmth during colder months.

The Cadet 80 is equipped with advanced technologies that enhance user experience and efficiency. It incorporates an easy-to-use adjustable thermostat that allows homeowners to set their desired temperature with precision. This feature not only maximizes comfort but also contributes to energy savings, as the system can automatically adjust its output based on the room’s heating needs.

Another hallmark of the Cadet 80 is its safety features. The heater includes a built-in overheat protection mechanism, providing peace of mind for users. This feature automatically shuts off the unit if it becomes too hot, preventing potential hazards and ensuring safe operation. Furthermore, the durable, heavy-duty construction of the Cadet 80 ensures longevity, withstanding the rigors of daily use.

Additionally, the easy installation process of the Cadet 80 is worth noting. The unit can be hardwired directly into the electrical system, making it suitable for permanent installation in various settings. This eliminates the need for cumbersome cords and allows for a cleaner aesthetic.

In summary, the International Home Products Cadet 80 electric wall heater stands out for its compact design, efficient heating capacity, user-friendly controls, and emphasis on safety. For those seeking a reliable and stylish heating solution for small to medium rooms, the Cadet 80 presents an excellent choice, merging modern technology with practical features that enhance comfort and convenience.
Top Page Image Contents