(131) MODEL CS8110 SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 07/28/2010
English 131
TROUBLESHOOTING GUIDE (continued)
LED PANELLED Panel Code Flash & Alarm On (NOTE: Always turn off the power before cleaning and servicing).
|
|
|
|
| 1. Filter pump not attached to |
| • | Ensure filter pump is attached and |
|
|
|
|
|
| |||
|
|
|
|
|
| |||
|
|
|
|
| system and/or switch on. |
| • | operating. See "Setup Instruction". |
|
|
|
|
| 2. Circulation line is blocked. |
| If your unit has plunger valves, ensure | |
|
|
|
|
|
|
| • | that they are open. |
|
|
|
|
|
|
| Clear your filter cartridge and cell from | |
|
|
|
|
|
|
| • | debris and dirt. See “Maintenance”. |
|
|
|
|
|
|
| Release all trapped air in the circulation | |
|
|
|
|
|
|
| • | line. See the filter pump manual. |
|
|
|
|
| 3. Incorrect inlet and outlet hose |
| Check the direction of the inlet and the | |
|
|
|
|
| direction. |
|
| outlet hose. Reverse the hoses if |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| • | necessary. See “Set Up Instructions”. |
|
|
|
|
| 4. Incorrectly installed flow sensor |
| Check that the arrow on the flow sensor | |
|
|
|
|
| conduit. |
|
| conduit points in the same direction as |
|
|
|
|
|
|
|
| the one on the cell. Reverse the flow |
|
|
|
|
|
|
| • | sensor conduit if necessary. |
|
|
|
|
| 5. Scale on the flow sensor. |
| Clean the flow sensor, paying special | |
|
|
|
|
|
|
|
| attention to the hinge. See |
|
|
|
|
|
|
| • | “Maintenance”. |
|
|
|
|
| 6. Flow sensor cord is loose. |
| Plug the flow sensor firmly into the flow | |
|
|
|
|
|
|
| • | sensor receptacle. |
|
|
|
|
| 7. Flow sensor failure. |
| Contact Intex Service Center. | |
|
|
|
|
| 8. Inner timer conflict between |
| • | Reset both timers on the filter pump and |
|
|
|
|
| filter pump and saltwater system. |
| • | saltwater system.See “Boost Cycle”. |
|
|
|
|
| 1. Dirt or scale on titanium plates. |
| Remove the electrolytic cell for | |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| inspection. Clean it if necessary. |
|
|
|
|
|
|
| • | See “Maintenance”. |
|
|
|
|
| 2. Low salt level / No salt. |
| Add salt. See “Salt & Pool Water | |
|
|
|
|
|
|
| • | Volumes”. |
|
|
|
|
| 3. Electrolytic cell cord is loose. |
| Ensure that the cell cord is plugged | |
|
|
|
|
|
|
| • | firmly into the cell housing receptacle. |
|
|
|
|
|
|
| ||
|
|
|
|
| 4. Possible electrolytic cell failure. |
| Contact Intex Service Center. Replace | |
|
|
|
|
|
|
|
| the cell if needed. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1. High salt level. |
| • | Partially drain the pool and refill it with |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| fresh water. See “Salt & Pool Water |
|
|
|
|
|
|
|
| Volumes”. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1. Display and all lights are off - the |
| • | Household voltage is too high or too low |
|
|
|
|
|
| |||
|
|
|
|
| system does not power up. |
|
| (+ 20%). Check the voltage is within the |
|
|
|
|
|
|
|
| range stated on the device housing. |
|
|
|
|
|
|
| • Contact Intex Service Center. | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TROUBLESHOOTING GUIDE
SAVE THESE INSTRUCTIONS
Page 26