![](/images/new-backgrounds/1304944/30494421x1.webp)
DRIVE ARM/SUPPORT BRACKET | PROCEDURE 4 |
This procedure includes the following:
Installing CLD on Existing Wheelchair
Replacing Support Bracket
Replacing Drive Arm Assembly
Mounting/Removing Support Bracket To/From Wheelchair
Removing/Installing Support Bracket To/From Drive Arm Assembly
Installing/Removing Drive Arm Assembly To/From Transmission
Installing/Removing Drive Arm
Adjusting Drive Arm Release Lever/Bracket Release Lever
Adjusting Drive Arm Height
WARNING
AfterANYadjustments,repairorserviceandBEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result.
INSTALLING CLD ON EXISTING WHEELCHAIR
1.Mount the support bracket onto the wheelchair. Refer to MOUNTING/REMOVING SUPPORT BRACKET TO WHEELCHAIR in this procedure of the manual.
2.Install the drive arm assembly onto the transmission. Refer to INSTALLING/REMOVING DRIVE ARM ASSEMBLY TO/FROM TRANSMISSION in this pro- cedure of the manual.
3.Install the drive arm. Refer to INSTALLING/REMOV- ING DRIVE ARM in this procedure of the manual.
4.Adjust the drive arm release lever. Refer to ADJUST- ING DRIVE ARM RELEASE LEVER in this procedure of the manual.
5.Adjust the drive arm height. Refer to ADJUSTING DRIVEARMHEIGHTin this procedure of the manual.
REPLACING SUPPORT BRACKET
1.Remove the EXISTING support bracket from the wheelchair. Refer to MOUNTING/REMOVING SUP- PORT BRACKET TO WHEELCHAIR in this proce- dure of the manual.
2.Remove the EXISTING support bracket from drive arm assembly. Refer to REMOVING/INSTALLING SUPPORT BRACKET TO/FROM DRIVE ARM AS- SEMBLY in this procedure of the manual.
3.Install the NEW support bracket onto drive arm as- sembly. Refer to REMOVING/INSTALLING SUP-
PORT BRACKET TO/FROM DRIVE ARM ASSEM- BLY in this procedure of the manual.
4.Install the NEW support bracket onto the wheelchair. Refer to MOUNTING/REMOVING SUPPORT BRACKET TO WHEELCHAIR in this procedure of
the manual.
REPLACING DRIVE ARM ASSEMBLY
1.Remove the EXISTING support bracket. Perform STEPS
2.Remove the EXISTING steering link. Refer to RE- MOVING/INSTALLING STEERING LINK in PRO- CEDURE 6 of the manual.
3.Remove the EXISTING drive arm assembly from the transmission. Refer to INSTALLING/REMOVING DRIVEARMASSEMBLYTO/FROMTRANSMISSION in PROCEDURE 6 of the manual.
4.Reinstall the EXISTING steering link. Refer to RE- MOVING/INSTALLING STEERING LINK in PRO- CEDURE 6 of the manual.
5.Reinstall the EXISTING support bracket onto the NEW drive arm assembly. Perform STEPS 1, 2 AND 4 in
REMOVING/INSTALLINGSUPPORTBRACKETTO/ FROM DRIVE ARM ASSEMBLY in this procedure of the manual.
6.Install the NEW drive arm assembly onto the trans- mission. Refer to INSTALLING/REMOVING DRIVE ARM ASSEMBLY TO/FROM TRANSMISSION in this procedure of the manual.
MOUNTING/REMOVING SUPPORT BRACKET TO/FROM WHEELCHAIR (FIGURE 1)
Mounting
1.Secure the bottom clamp and the spacer plate to the wheelchair and the support bracket with the two
(2)flat screws as shown in FIGURE 1. Torque to 7 ft./lb. (84 in./lb.).
2.Secure the 1 inch clamp to the wheelchair and the support bracket with the two (2) hex screws, flat wash- ers and hex nuts. Torque to 7 ft./lb. (84 in./lb.).
Removing
1.Remove the two (2) flat head screws securing the bottom clamp and the spacer plate to the wheelchair.
2.Remove the two (2) hex screws, washers and hex nuts securing the
D R I V E
A R M
S U P P O R T
B R A C K E T
11