Manuals / Invacare / Fitness & Sports / Camping Equipment

Invacare MA95Z, MA90Z manual Powering Up the System, Lock/Alarm Silence Button, Power Fail LED

Models: MA95Z

1 28

Download 28 pages 24.06 Kb

Page 19

Lock/Alarm Silence Button

SECTION 2—OPERATION

Lock/Alarm Silence Button

1.Press the Lock/Alarm Silence button () to select one of the following modes:

•Lock Mode ‐ Pressing this button locks out all control unit functions, including the On button, to prevent any tampering with the settings. Press the button for approximately 3‐5 seconds for the Lock LED to activate.

NOTE: The Lock LED illuminates when in this mode.

•Alarm Silence mode ‐ Pressing this button silences the alarm that sounds in the event of power failure or when the hose is disconnected from the control unit.

NOTE: The Alarm LED illuminates when in this mode.

Power Fail LED

In the event of power outage, an alarm sounds and the Power Fail LED flashes AMBER. The control unit has internal memory and retains the previous settings during the power outage.

NOTE: During a power outage, the MA90Z mattress retains the air as long as the mattress is connected to the control unit.

Low Pressure LED

In the event that the mattress hose disconnects, an alarm sounds and Low Pressure LED flashes AMBER. Once the low pressure problem is fixed, the control unit resumes operation in the previously set mode.

Displaying the Total Run Time (MA95Z)

Every time the control unit is plugged in, the LCD screen displays the Run Time in hours and minutes. For example, 2,584 hours and 25 minutes displays as 002584 Hours 000025 Minutes.

To display the Run Time during use:

1.Ensure the control unit is plugged in and the Standby LED is On.

2.Press and hold the Soft and Firm Buttons at the same time.

3.The LCD screen displays the Run Time as described above.

Powering Up the System

NOTE: For this procedure, refer to FIGURE 2.4.

1. Turn on the power to the system by pressing the Power button on the control unit.

NOTE: Once the button is released, a GREEN LED illuminates when the unit is on.

Part No 1148139

19

MA90 Series

Image 19

Invacare MA95Z, MA90Z manual Powering Up the System, Lock/Alarm Silence Button, Power Fail LED, Low Pressure LED

Contents

MA95Z Alternating Rotation and True Low Air Loss System Owner’s Operator and Maintenance ManualMA90 Series MA90Z Alternating Rotation with On Demand True Low Air Loss SystemSPECIAL NOTES ACCESSORIES WARNINGTYPICAL PRODUCT PARAMETERS TABLE OF CONTENTSSPECIAL NOTES REGISTER YOUR PRODUCTSECTION 3-MAINTENANCE AND TROUBLESHOOTING REGISTER YOUR PRODUCTTABLE OF CONTENTS Register ONLINE at warranty.invacare.comElectrical Parameters TYPICAL PRODUCT PARAMETERSPerformance Parameters CONTROL UNIT WEIGHT Mechanical ParametersEnvironmental Parameters CONTROL UNIT DIMENSIONS L X W X HNOTE MA95Z only LABEL LOCATIONNOTE This label is on the foot end of the mattress cover not shown Entrapment May Occur InstallationSECTION 1-GENERAL GUIDELINES ContraindicationsAnesthesia Equipment Fire HazardElectrical DANGER SmokingSECTION 2-OPERATION Installing the Mattress Replacement SystemNOTE For this procedure, refer to FIGURE NOTE The powered mattress comes with ten nylon buckle strapsNOTE For this procedure, refer to FIGURE Installing the Side RailsInstalling the Power Unit NOTE Mattress cover not shown for clarityNOTE For this procedure, refer to FIGURE Connecting the HoseConnecting the Power Cord Power Button Using the Front PanelNOTE For this procedure, refer to FIGURE Rotation Button MA95Z Turn Button MA90ZTurn Time Button MA90Z Turn Angle Button MA90ZAbout Automatic Wireless Mode Automatic Wireless FowlerHold Button MA95Z Firm/Soft ButtonsProgramming the Automatic Wireless Fowler Transmitter NOTE The control unit will beep and will return to StandbySECTION 2-OPERATION Mode Button MA90ZMax Inflate Button MA95Z NOTE This will deactivate the Max Inflate LEDNOTE The Lock LED illuminates when in this mode Powering Up the SystemLock/Alarm Silence Button Power Fail LEDTransferring Patient From/To a Gurney Placing the Patient on the MattressNOTE In this mode, the Max Inflate LED lights up Transferring Patient From/To a Wheelchair Preparing for CPR ProcedureNOTE For this procedure, refer to FIGURE DETAIL “A” FIGURE 2.5 Preparing for CPR ProcedureSECTION 2-OPERATION DETAIL “B”Cleaning the System SECTION 3-MAINTENANCE AND TROUBLESHOOTINGDO NOT overload the machine Storing the SystemDO NOT use chlorine bleach because it may damage the fabric coating NOTE For this procedure, refer to FIGURE 3.1 on page TroubleshootingChanging the Filter No power MA90 Series SECTION 3-MAINTENANCE AND TROUBLESHOOTINGCanada LIMITED WARRANTY