Manuals / Invacare / Fitness & Sports / Camping Equipment

Invacare MA95Z, MA90Z manual NOTE The control unit will beep and will return to Standby

Models: MA95Z

1 28

Download 28 pages 24.06 Kb

Page 17

Programming the Automatic Wireless Fowler Transmitter

SECTION 2—OPERATION

Programming the Automatic Wireless Fowler Transmitter

1.Ensure the transmitter is inside the mattress pocket located on the right side of the mattress at the head end.

2.Ensure the mattress is in a flat position.

3.Ensure the control unit is plugged in, and the LCD displays STAND BY.

4.Perform one of the following:

• MA90Z ‐ Perform the following steps:

i. Press and hold the Turn Angle and Max Inflate buttons.

NOTE: The Fowler LED is lit and L displays in the LCD Display. ii. Raise the bed to 45°.

NOTE: The control unit will beep and will return to Standby.

iii.Perform one of the following:

•Cancel ‐ Press the Turn Angle button to exit Fowler Transmitter Setup without linking to a transmitter.

•Save ‐ Wait 60 seconds without pressing a key.

•MA95Z ‐ Perform the following steps:

i.Press and hold the Hold and Max Inflate buttons.

ii.AUTO FOWLER LEARN MODE will display.

iii.PLACE BED IN FLAT POSITION will display.

iv.CONTINUE ‐> SELECT will display.

v.Press the Select button.

vi.PLACE BED IN FOWLER/UPRIGHT POSITION will display.

vii.TRANSMITTER DETECTED will display.

viii.The control unit will beep. ix. STAND BY will display.

Part No 1148139

17

MA90 Series

Image 17

Invacare MA95Z, MA90Z manual NOTE The control unit will beep and will return to Standby

Contents

MA90 Series Owner’s Operator and Maintenance ManualMA90Z Alternating Rotation with On Demand True Low Air Loss System MA95Z Alternating Rotation and True Low Air Loss SystemSPECIAL NOTES ACCESSORIES WARNINGSPECIAL NOTES TABLE OF CONTENTSREGISTER YOUR PRODUCT TYPICAL PRODUCT PARAMETERSTABLE OF CONTENTS REGISTER YOUR PRODUCTRegister ONLINE at warranty.invacare.com SECTION 3-MAINTENANCE AND TROUBLESHOOTINGPerformance Parameters TYPICAL PRODUCT PARAMETERSElectrical Parameters Environmental Parameters Mechanical ParametersCONTROL UNIT DIMENSIONS L X W X H CONTROL UNIT WEIGHTNOTE This label is on the foot end of the mattress cover not shown LABEL LOCATIONNOTE MA95Z only SECTION 1-GENERAL GUIDELINES InstallationContraindications Entrapment May OccurElectrical Fire HazardDANGER Smoking Anesthesia EquipmentNOTE For this procedure, refer to FIGURE Installing the Mattress Replacement SystemNOTE The powered mattress comes with ten nylon buckle straps SECTION 2-OPERATIONInstalling the Power Unit Installing the Side RailsNOTE Mattress cover not shown for clarity NOTE For this procedure, refer to FIGURENOTE For this procedure, refer to FIGURE Connecting the HoseConnecting the Power Cord NOTE For this procedure, refer to FIGURE Using the Front PanelPower Button Turn Time Button MA90Z Turn Button MA90ZTurn Angle Button MA90Z Rotation Button MA95ZHold Button MA95Z Automatic Wireless FowlerFirm/Soft Buttons About Automatic Wireless ModeProgramming the Automatic Wireless Fowler Transmitter NOTE The control unit will beep and will return to StandbyMax Inflate Button MA95Z Mode Button MA90ZNOTE This will deactivate the Max Inflate LED SECTION 2-OPERATIONLock/Alarm Silence Button Powering Up the SystemPower Fail LED NOTE The Lock LED illuminates when in this modeNOTE In this mode, the Max Inflate LED lights up Placing the Patient on the MattressTransferring Patient From/To a Gurney NOTE For this procedure, refer to FIGURE Preparing for CPR ProcedureTransferring Patient From/To a Wheelchair SECTION 2-OPERATION FIGURE 2.5 Preparing for CPR ProcedureDETAIL “B” DETAIL “A”Cleaning the System SECTION 3-MAINTENANCE AND TROUBLESHOOTINGDO NOT use chlorine bleach because it may damage the fabric coating Storing the SystemDO NOT overload the machine Changing the Filter TroubleshootingNOTE For this procedure, refer to FIGURE 3.1 on page No power MA90 Series SECTION 3-MAINTENANCE AND TROUBLESHOOTINGCanada LIMITED WARRANTY