JBL CS 360 Xcite owner manual Lipsnc, Disply, On Vol, Name, Au On, Au Src, Reset?

LIPSNC:

Lip Sync delays audio so that it is in sync with video that may be delayed due to processing. When the Display shows LIPSNC blinking, press SET. The Display now shows the standard value of 50 ms (milliseconds). You may adjust the Delay in 5 ms increments from 0 ms to 100 ms by pressing the Up and Down Navigation Buttons. Adjust until audio from the speakers follows the lip movements on the TV screen. Press SET or EXIT to save the setting and move to next adjustment.

DISPLY:

The Display option lets you choose between either Timeout YES or NO with the Left and Right Navigation Buttons. If you select T/O NO, the Display shows infor- mation at all times. If you select T/O YES, the Display goes dark three seconds after your last action.

Please note that when you have selected Time Out YES, most of the commands from the Remote Control must be sent twice, first time to activate the Display, second time to perform the command. However, if Power Off, Volume Up, Volume Down or Mute is pressed when the Display is dark, it lights up, but the command is also executed. If you select Timeout NO, only one press on any Button is necessary, as there is no need to wake up the Display first.

Press SET or EXIT to save the setting and move to next adjustment.

ON VOL:

On Vol lets you decide the start-up Volume of the sys- tem. Press SET when ON VOL blinks. Now you can choose between OV OFF or OV plus a number with the Right and Left Navigation Buttons. OV OFF means that the system is silent when you switch it on, and you must increase the Volume from zero to desired volume every time it has been switched off. OV60 means that the system always starts up at the volume represented by the number 60. This number can be changed from 0 and up, in increments of one. If you select OVxx, you can increase and decrease the startup volume (and the number) with the Up and Down Navigation Buttons, and you can hear the actual volume while you are changing it. Just choose a comfort- able startup volume, followed by a press on SET or EXIT to save the setting and move to the next adjustment. If you do nothing for three seconds, the system reverts to the Setup Menu by itself.

NAME:

Permits you to add a name to any Input, up to six charac- ters long.

When NAME blinks in the Display, press SET. The name of the first input is shown in the dot-matrix display line, with the entire name blinking above in the fixed-character sec- tion. You may now jump from input to input with the Left and Right Navigation Buttons until you see the one you want to name. (If you are listening to a signal source, it remains active while you rename any or all inputs). Now press SET again. The first character blinks. Now use the Up and Down Navigation Buttons to run through the let- ters of the alphabet, the digits 0-9 and various symbols. Search forwards or backwards. When you have run through all characters, the list begins again from the start. You can also select digits directly with the 0-9 alphanumeric buttons. Confirm you selection and jump to the next one (which now blinks) with the Right Navigation Button. Repeat the procedure until the name is entered, then press SET to skip to the next input. When you are done naming inputs, press EXIT once to skip to the next Setup item, or twice to leave Setup.

AU ON:

Activates or deactivates the AUTO TURN ON feature. This feature is explained at the start of this manual, but briefly it automatically switches the system ON when it senses a signal. The default setting is YES. With AU ON blinking, press SET on the Remote. You can select YES (not blinking) or NO (not blinking) with the Left and Right Navigation Buttons. Confirm your selec- tion by pressing SET again, or press EXIT to skip to the next Setup item.

AU SRC:

Activates or deactivates the AUTO SOURCE SELECTION fea- ture, which senses what Input you are currently using. The default setting is YES. If you would prefer to do the Input selection manually, choose NO. With AU SRC blinking press SET on the Remote. You can select YES (not blink- ing) or NO (not blinking) with the Left and Right Navi- gation Buttons. Confirm your selection by pressing SET again, or press EXIT to skip to the next Setup item.

RESET?

If you press SET, when RESET? is shown blinking, the Dis- play asks you to confirm with the word SURE? blinking. If you press EXIT now, nothing is reset, and the unit leaves the SETUP menu. If user press SET once again, all SETUP settings go back to factory default settings. RESET also sets BASS and TREBLE settings back to 0:

12