INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

Level

Drill

1¼" (3 cm) drill bit

¹⁄₈" (3 mm) drill bit if installing into wood and a ⁵⁄₁₆" (8 mm) drill bit if installing optional backsplash kit.

Pencil

Wire stripper or utility knife

Tape measure or ruler

Pliers

Caulking gun and weatherproof caulking compound

Vent clamps

Jigsaw or keyhole saw

Flat-blade screwdriver

Metal snips

Phillips screwdriver

Scissors

Parts needed

Home power supply cable

1 - ½" (12.7 mm) UL listed or CSA approved strain relief

3 UL listed wire connectors

1 wall or roof cap

Metal vent system

Parts supplied

Remove parts from packages. Check that all parts are included.

2 metal grease filters for 30" (76.2 cm) models

3 metal grease filters for 36" (91.4 cm) models

4 metal grease filters for 48" (121.9 cm) models

Damper

Hood canopy with blower and halogen lamps installed.

1 - 10" (25.4 cm) square to 10" (25.4 cm) round duct transition.

2 - 175 watt infrared heat lamps

Wood support

Grease collectors

4 - 6 x 80 mm mounting screws

4 - 3.5 x 9.5 mm screws

6 - 4.2 x 19 mm screws

5 - M6 x 16 mm screws

5 - D6.4 x 11 mm washers

2 - D5.3 x 20 mm washers

2 - 10 x 50 mm wall anchors

T20® TORX®†adapter

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the rear wall of the range hood.

Canopy range hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

The canopy range hood is factory set for venting through the roof or through the wall.

All openings in ceiling and wall where canopy range hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes.

Product Dimensions

Front view

18¹⁄₁₆" (45.9 cm) for 48" (121.9 cm) Hood 12¹⁄₁₆" (30.6 cm) for 36" (91.4 cm) Hood 9¹⁄₁₆" (23.0 cm) for 30" (76.2 cm) Hood

CL

6¹⁄₂" (16.5 cm)

12" (30.5 cm)

18" (45.7 cm)

2¹⁄₄"

(5.7 cm) 25" (63.5 cm)

30" (76.2 cm) 36" (91.4 cm)

48" (121.9 cm)

†®TORX and T20 are registered trademarks of Saturn Fasteners, Inc.

5

Page 5
Image 5
Jenn-Air LI3UNB/W10274316B installation instructions Installation Requirements, Tools and Parts, Location Requirements

LI3UNB/W10274316B specifications

Jenn-Air LI3UNB/W10274316B is an innovative kitchen appliance that brings a sophisticated touch to modern cooking. Designed for discerning culinary enthusiasts, this built-in refrigerator embodies luxury, style, and advanced technology.

One of the standout features of the Jenn-Air LI3UNB is its impressive capacity. With a spacious interior, it provides ample room for all your food and beverages. Its flexible shelving and storage options allow you to configure the layout according to your needs, accommodating everything from tall bottles to small jars.

This refrigerator is equipped with advanced cooling technologies, including the Dual Evaporator system. By utilizing separate evaporators for the refrigerator and freezer compartments, it ensures optimal humidity levels and prevents odor transfer between sections. This technology maintains the freshness of food for longer periods, allowing you to shop for groceries less frequently while enjoying the quality of your ingredients.

The exterior of the LI3UNB is just as striking as its interior. With a sleek and stylish stainless-steel finish, it seamlessly integrates into any kitchen design, exuding elegance and modernity. The appliance comes with an integrated ice maker, offering the convenience of fresh ice without the need for bulky ice trays.

Control is made effortless with the intuitive digital interface, providing users with an easy way to set temperatures, activate functions, and monitor the refrigerator’s performance. The bright interior LED lighting illuminates every corner, allowing for easy visibility of stored items, even when it's packed full.

Energy efficiency is another significant attribute of the Jenn-Air LI3UNB/W10274316B. The appliance meets stringent energy standards, contributing to lower utility bills while minimizing environmental impact. Its Energy Star rating ensures that it operates efficiently without compromising on performance.

In addition to its functional features, the LI3UNB also boasts an ultra-quiet operation, making it an ideal choice for open-concept living spaces. The carefully engineered compressor and cooling system allow it to run quietly, ensuring that it doesn’t disrupt your home environment.

In summary, the Jenn-Air LI3UNB/W10274316B is more than just a refrigerator; it’s a sophisticated appliance designed to meet the needs of today’s modern kitchens. With its spacious design, advanced cooling technologies, energy efficiency, and elegant aesthetics, it stands out as a premium choice for anyone looking to enhance their culinary experience.