Jensen DV2007 DIN Front Mount Method a, Removing the Unit, Trim Plate Installation

Bend Tabs

Screw Stud

DV2007

3. INSTALLATION

Before You Begin

1.Disconnect Battery

Before you begin, always disconnect the battery negative terminal.

2.Remove Transport Screws

Important Notes

•Before final installation, test the wiring connections to make sure the unit is connected properly and the system works.

•Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

•Consult with your nearest dealer if installation requires the drilling of holes or other modifications to your vehicle.

•Install the unit where it does not interfere with driving and cannot injure passengers if there is a sudden or emergency stop.

•If the installation angle exceeds 30º from horizontal, the unit might not give optimum performance.

•Avoid installing the unit where it will be subject to high temperatures from direct sunlight, hot air, or from a heater, or where it would be subject to excessive dust, dirt or vibration.

•Be sure to remove the control panel before installing the unit.

DIN Front/Rear Mount

This unit can be property installed with either a “Front” (conventional DIN front mount) or “Rear” (DIN rear mount installation, utilizing threaded screw holes at the sides of the unit chassis)

recheck all wiring until the problem is corrected. Once proper operation is achieved, turn the ignition switch off and proceed with final mounting of the chassis.

8.Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring clips lock it into place.

9.Attach one end of the

perforated support strap	Dashboard
(supplied) to the screw stud on	Support Strap
the rear of the chassis using
the hex nut and spring washer	Plain Washer
provided. Fasten the other end
	Screw (4 x 12mm)
of the perforated strap to a
secure part of the dashboard	Screw Stud
either above or below the radio	Hex Nut (5mm)
using the screw and plain	Spring Washer
washer provided. Bend the
strap, as necessary, to position
it. CAUTION: The rear of the
radio must be supported with

the strap to prevent damage to the dashboard from the weight

of the radio or improper operation due to vibration.

10.Re-attach the front panel to the chassis and test radio operation by referring to the operating instructions for the unit.

mount. For details, refer to installation methods A and B.

DIN Front Mount (Method A)

1. Remove the detachable front panel, if it is Dashboard attached to the chassis, by pushing the

REL button.

182

2.Slide the mounting sleeve off of the chassis if it has not already been removed.

53

If it is locked into position, use the removal keys (supplied) to disengage it. The removal keys are depicted on page 4.

3.	Check the dashboard opening size by
	sliding the mounting sleeve into it. If the
	opening is not large enough, carefully cut
	or file as necessary until the sleeve easily
	slides into the opening. Do not force the sleeve into the opening or cause it to bend or
	bow. Check that there will be sufficient space behind the dashboard for the radio chassis.
4.	Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve.
	With the sleeve fully inserted into the dashboard opening, bend as many of the tabs

Removing the Unit

To remove the radio after installation:

1.Insert fingers into the groove in the front of frame and pull out to remove the frame. (When re-attaching the frame, point the side with a groove downwards and re- attach.)

2.Insert the removal keys straight back until they click, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit.

Trim Plate Installation

Push the trim plate against the chassis until it is fitted. You must do this before you install the

control panel, otherwise it can't be attached.

DIN Rear Mount (Method B)

Dashboard

Removal Key

	outward as necessary to firmly secure the sleeve to the dashboard.
5.	Place the radio in front of the dashboard opening so the wiring can be brought through the
	mounting sleeve.
6.	Follow the wiring diagram carefully and make certain all connections are secure and
	insulated with crimp connectors or electrical tape to ensure proper operation.
7.	After completing the wiring connections, attach the front panel and turn the unit on to
	confirm operation (vehicle ignition switch must be on). If the unit does not operate,

This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some vehicles to mount the radio to the dashboard. Please consult with your local mobile stereo shop for assistance on this type of installation.

1.Remove the existing factory radio from the dashboard or center console mounting. Save all hardware and brackets as they will be used to mount the new radio.

2.Carefully unsnap the plastic trim ring from the front of the new radio chassis. Remove and

3discard the trim ring.