Jensen owner manual JHD1000 Configuration, Wiring, Configuration of the World Band Tuner

JHD1000

Configuration (continued)

Country Code	Country	Band	Low	High	Step
11	North America	AM	530	1710	10kHz
		FM	87.9	107.9	200kHz
12	Europe	SW	5900	6200	5kHz
		AM	531	1629	9kHz
		FM	87.50	108.00	50kHz
		LW	144	288	9kHz
13	Pacific	AM	531	1629	9kHz
		FM	87.5	108.0	100kHz
14	Japan	AM	522	1629	9kHz
		FM	76.0	90.0	100kHz
15	Latin America	AM	530	1600	10kHz
		FM	88.0	108.0	100kHz

Wiring

The wiring diagram depicts all the wiring connections required for proper operation of the unit.

16	Brazil	AM	530	1620	10kHz
		FM	87.9	107.9	200kHz
21	Saudi Arabia	AM	531	1602	9kHz
		FM	87.5	108.0	50kZHz

Configuration of the World Band Tuner

Press AUDIO ADJUST for more than three seconds. The unit will enter the general configuration menu. To enter the tuner configuration menu, press preset 4, then preset 2. "CC--**" will appear on the display (where ** can equal 11, 12, 14, 15, 16 or 21). Use the up tuning button to select the proper country code for the region of interest. The country codes are listed above. To exit, press AUDIO ADJUST again or the configuration menu time out (takes about five seconds).

DIN CONNECTOR

SEE PAGE 4 FOR LOW

LEVEL AUDIO INPUT

PINK (TRIGGER) - SEE CHART C

*SPEAKER WIRES ARE BONDED PAIRS NEGATIVE GRAY WIRES PAIRED WITH RESPECTIVE POSITIVES

*SOLDER AND TAPE ALL SPLICES

9 PIN CABLE

CONNECTOR

BLACK/WHITE (GROUND)

TO ANTENNA

Wiring Color Codes

	2-Bond Pair	Gray	Left Front (-)
		Gray/White	Left Front (+)
From 9-Pin		Orange/White	Ignition
		Black	Chassis Ground
Harness		Pink	12V Out 100mA
		Green/White	Memory
	2-Bond Pair	Gray	Right Front (-)
		Gray/Blue	Right Front (+)
From 4-Pin	2-Bond Pair	Gray	Right Rear (-)
		Gray/Yellow	Right Rear (+)
Harness	2-Bond Pair	Gray	Left Rear (-)
		Gray/Red	Left Rear (+)

4 PIN CABLE CONNECTOR

Configuration of 2 and 4 Speaker Operation

Press AUDIO ADJUST for more than three seconds. The unit will enter the general configuration menu. Press the up tuning button until "SP--**" appears in the display (where ** can equal 2 or 4). Change this menu item according to the desired setup by using the up tuning button to modify the setting to either "SP-2" or "SP-4". To exit, press AUDIO ADJUST again or the configuration menu time out (takes about five seconds).

Configuration of Tuner Seek Sensitivity Setting

The scan sensitivity feature is designed to give flexibility during the tuner seek function. The tuner can be configured such that during seek, it will stop on strong stations, ignoring weaker signals. The tuner can also be configured to stop at all weak signals.

To configure the seek sensitivity setting, press AUDIO ADJUST for more than three seconds. The unit will enter the general configuration menu. While in the general configuration menu, press preset 4 and then preset 2. The unit is now in the tuner configuration menu. Press the up tuning button until "SC--**" appears in the display (where ** can equal 00-15). The numbers are set such that at the setting "SC-00", the unit is more sensitive to weaker signals. This means that the seek function will stop at most or all weak signals. At "SC-15", the seek function will stop only at the strong stations. Use the up tuning button to adjust the seek sensitivity of the tuner to a setting that will suit the application. To exit, press AUDIO ADJUST again or the configuration menu time out (takes about five seconds)..

GREEN/WHITE (BATTERY +12V) - SEE CHART A

ORANGE/WHITE (ACC. +12V) - SEE CHART B

LEFT FRONT SPEAKER	RIGHT FRONT SPEAKER
GRAY (-)	GRAY (-)
GRAY/WHITE (+)	GRAY/BLUE (+)
4 OR 8 OHM	4 OR 8 OHM
LEFT REAR SPEAKER	RIGHT REAR SPEAKER
GRAY (-)	GRAY (-)
GRAY/RED (+)	GRAY/YELLOW (+)
4 OR 8 OHM	4 OR 8 OHM

3