VM9313
OPERATING INSTRUCTIONS
Power On / Off
Press the
/SRC button (6) on the unit (or the
button (4) on the remote control) to turn the unit on. The buttons on the front of the unit light up and the current mode status appears in the LCD screen (15). You can also turn on the unit by pressing the OPEN button (4) and opening the TFT screen.
Press and hold the
button to power off the unit.The monitor is drawn back into the main compartment.
Audible Beep Confirmation
An audible beep tone confirms each function selection. The Beep tone can be disabled through the Setup menu.
Mute
Press the AUDIO button (5) on the front panel or the MUTE button (3) on the remote to mute the volume from the unit. Press the button again to restore the volume. “MUTE” is displayed on the LCD. Adjusting the volume or using any of the audio setup features cancels the mute function.
Playing Source Selection
Press the SRC button (6) on the front panel or the SRC button (8) on the remote to change between available playing sources. The playing mode is displayed on the TFT and LCD screens.
auxiliary device connected to the A/V INPUT on the front of the radio. You cannot directly control external devices connected to the A/V INPUT.
Selecting a Source While Navigating
While navigating, other sources may be selected and listened to such as 
/SRC button (6) and then select a source from the Front Source Menu. Navigation voice prompts will be heard automatically, although the navigation map cannot be seen. (The selected source audio will be muted until the navigation voice prompt command is completed, after which the source audio will resume.)
Volume Adjustment
To increase or decrease the volume level, turn the AUDIO control (5) on the front panel or press the VOL+/ VOL- buttons (15, 16) on remote control. When the volume level reaches “0” or “40”, a beep sounds, indicating that the adjustment limit has been reached. The volume ranges from “0” to “40”. The LCD or TFT screen displays the volume level for 3 seconds.
Programmable Turn-On Volume
This feature allows the user to select a
8.** Select
9.Band
**If additional steering wheel control buttons are available on the vehicle, function 7 / 8 may be assigned the "Select" feature. This feature / function may not be available on some vehicles.
Select Operation
If "Select" (function 7 or 8) is held down and function 4 is pressed momentarily, Preset Up will be selected. If "Select" (function 7 or 8) is held down and function 5 is pressed momentarily, Preset Down will be selected.
Audio Control Menu
The Audio Control feature allows you to easily adjust your audio system to meet the acoustical characteristics of your vehicle, which vary depending on the type of vehicle and its measurements. Proper setting of the Fader and Balance boosts the effects of the cabin equalizer.
Press the AUDIO button (5) on the front panel or touch the EQ button on the left side of the TFT screen to display the audio menu.
|
| EQ |
|
|
| User |
|
|
|
|
|
| FAD |
| BAL | ||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F | |
Accessing External Devices
External peripheral devices can be connected to this unit via the rear RCA inputs or the A/V INPUT connector (11) on the front of the unit. Select
control (5) to adjust the volume to the desired
Steering Wheel Control (SWC)
The VM9313 is compatible with the PAC (Pacific Accessory Corporation) steering wheel control adapter
+14 —
0—
BASS
0 — |
|
— | L |
| |
MID TREB | SUB |
R
R
A / V |
|
|
INPUT | 1 | Right Audio |
| ||
| 2 | Left Audio |
| 3 | Ground |
| 4 | Video |
3.5mm Media Cable (included)
Connect the external device to the 3.5mm Media Cable and then plug the cable into the A/V INPUT connector (10) on the front of the radio. Select “AUX IN1” mode to access an
3.5mm female connector (labeled “SWC Interface”) on the back of the head unit allows connectivity to the PAC adapter. Please refer to the instructions included with the PAC adapter for detailed installation information.
SWC Functions
The following controls are available for most vehicles:
1.Vol Down
2.Vol Up
3.Mute
4.Seek Down / Previous Track / ** Preset Down
5.Seek Up / Next Track / ** Preset Up
6.SRC (Source)
7.** Select
User
To adjust an audio feature:
1.Use the touchscreen or press the (>>)/(<<) buttons (14, 22) on the remote control to highlight the audio feature to be adjusted.
2.Touch the screen to select an option to adjust. Touch the yellow box next to the “EQ” label or press the AUDIO control (5) repeatedly to view available preset EQ options.
3.Touch the +/– buttons on the screen or press the <<, >>, >>, or << buttons (17, 19, 14, 22) on the remote
8
