Wiring

Wiring Connections

1.TV TUNER

2.ANTENNA

3.POWER ANTENNA WIRE (Blue) – Connect to a motorized (power) antenna and/or to a remote turn-on lead for an amplifier.

4.CONSTANT POWER WIRE (Yellow) – Connect the 12V PLUS constant power wire to a live 12 volt wire in the vehicle. Before making a connection, check that the wire you intend to connect it to is always live, even when the car’s ignition is turned off. If a live wire is not found, route the wire to the car’s fuse block and connect it to a live circuit there.

5.GROUND WIRE (Black) – Securely fasten the Ground wire to a grounded metal part of the car’s chassis. If you cannot find an existing bolt or screw to fasten it to, drill a hole in the metal and secure it with a screw. To ensure a good ground, remove any paint or grease from areas where the wire will contact the surface.

6.PARKING (Pink) – Connect to negative parking brake wire. This wire MUST BE connected in accordance with federal, state and local laws. It is the end-user’s responsibility to make sure this wire is connected properly.

7.ACC POWER WIRE (Red) – Connect to a +12 volt circuit that is only live when the ignition is on. The best connection point is at the car’s fuse block at the “RADIO” or “ACCESSORY” identified terminals.

8.LEFT FRONT SPEAKER (white, white/black)

9.RIGHT FRONT SPEAKER (gray, gray/black

10.LEFT REAR SPEAKER (green, green/black)

11.RIGHT REAR ( + ) SPEAKER (violet, violet/black)

12.FRONT AND REAR RCA OUTPUTS

13.CENTER RCA OUTPUT (Gray) – The center output must be connected to an external amplifier for 3D or 6-CH mode.

14.SUBWOOFER RCA OUTPUT (Blue) – The subwoofer output is available in all sound/audio modes.

15.DEDICATED DVD OUTPUT – Video output for rear screen and left/right audio output for headphones.

16.AV1 INPUT

17.AV2 INPUT

18.VIDEO OUT (Yellow) - V. SEL output for rear screen.

Replacing the Fuse

When replacing a fuse, be sure to use correct type and amperage to avoid damaging the radio. The VM9510 uses one 10 amp AGC fuse, located in the black filter box in-line with the main wire harness.

Reconnecting the Battery

When wiring is complete, reconnect the battery negative terminal.

10A

15

13 14

3

Blue / Azul

/ Bleu

 

 

Front

Black

Frente

Negro

/ Noir

Avant

 

 

12

Rear

Gray

Posterior

 

Arrière

Gris / Gris

White/Black (-)

Blanco/Negro (-)

Blanc/Noir (-)

8

White / Blanco / Blanc (+)

Green/Black (-)

Verde/Negro (-)

Vert/Noir (-)

16

 

 

18

 

 

Yellow / Amarillo / Jaune

FIL TER

&

+

FUSE

BOX

 

 

Black / Negro / Noir

Pink

/ Rosa

/ Rose

 

 

6

Red / Rojo / Rouge

7

Antenna Included

la Antena Incluyó

Gray/Black (-)l'antenne a Inclus Gris / Negro (-)

Gris / Noir (-)

9

Gray / Gris / Gris (+)

Violet/Black (-)

Violeta/Negro (-)

Violet/Noir (-)

10

11

 

Green / Verde / Vert (+)

Violet / Violeta / Violet (+)

VM9510

2

17

4

5

1

 

 

 

 

- OITODAR

 

 

 

 

r ev

 

 

 

 

 

 

 

 

VrTenTuei ceR

 

 

 

 

 

 

 

 

0159 MV

RESVID

 

 

 

 

 

 

YTI

 

 

 

AN T

LA

OINT O P

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

3

2

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

Page 4
Image 4
Jensen VM9510 owner manual Wiring Connections, Replacing the Fuse, Reconnecting the Battery