Right angle cuts -- single pieces of stock

1.Raise the saw arm to its full up, open position.

2.Pull up on the quick release handle on the locking vise jaw and slide the vise jaws apart.

3.Place the stock on the saw table, between the vise jaws. If the stock is long, support the stock with appropriate infeed and outfeed supports.

4.Pull up on the quick release handle and slide the locking vise jaw up against the workpiece.

5.Turn the lead screw handle until the quick release thrust shaft falls into a groove on the lead screw and puts light clamping pressure on the workpiece.

6.Lower the saw arm until the blade is just above the workpiece.

7.Lock the saw arm in position by turning the hydraulic feed needle valve clockwise.

8.Adjust the position of the stock until the cut-off distance you require is directly under the blade.

9.Tighten the vise so the workpiece is clamped firmly.

Note: if you are sawing a workpiece with a sharp edge up -- use a file to knock off the sharp edge before beginning any saw cuts. This will prevent damage to teeth on the blade. See Figure 8 for details.

10.Turn the saw switch ON and allow the motor and blade to come up to full speed.

11.If using a coolant system, turn on the valve at the nozzle.

12.Carefully open the hydraulic control needle valve open (counterclockwise) so the cutting arm lowers gently into the workpiece and begins cutting.

13.Continue to open the hydraulic control valve until an efficient cutting rate is established.

14.When the saw completes its cut, the motor will shut off and the cut piece will fall away from the table.

15.If you are using a coolant system, turn it off the valve at the nozzle.

Table 1: Suggested cutting speeds

Suggested cutting speeds for a variety of materials. Speeds are recommended speeds for a 4 inch thick work piece, a bi-metal blade, dry cutting. (No cutting fluid. Speeds may be increased when cutting fluid is used -- observe chip formation to determine most efficient cutting rate.)

Decrease these speeds 30-50% for carbon steel blades. Increase speed 15% for materials 1/4 inch thick, 12% for materials 3/4 inch thick, 10% for materials 1 1/4 inch thick, and 5% for 2 1/2 inch thick material. Decrease speed

12% when cutting eight inch material. When selecting blade tooth pitch, be sure to have two or more teeth in contact with the material at all times to avoid tooth breakage.

Angle cutting

1.Raise the saw arm to full height and lock it in position with the quick shut off valve.

2.Slide the vise open.

3.Set the stationary vise jaw to the angle required according to the instructions in Adjusting stationary vise jaw.

4.Put the workpiece in position on the saw table.

5.Adjust the locking vise jaw to the workpiece using instructions in Adjusting the locking jaw.

6.Adjust the blade guide/support bearing brackets according to instructions in Setting the blade guides.

7.Release the quick shut off valve and lower the arm and blade to just above the workpiece, then lock the arm in position using the hydraulic cylinder control needle valve.

8.Adjust the workpiece to the required cut-off position under the blade.

9.Tighten the vise securely.

10.If you are starting your cut on a sharp edge, use a

file to knock off the sharp edge so the blade isn't damaged at the start of the cut.

11.If using coolant or cutting fluid, turn on valve at the nozzle.

12.Turn the saw switch ON.

13.Open the hydraulic cylinder needle valve until the blade contacts the workpiece and establishes a cut -- then open the control cylinder valve until the blade is cutting efficiently.

14.When the cut is completed the motor will turn off and the cut piece will fall away from the saw. Turn off the coolant flow and repeat the steps above as necessary to continue with more cuts.

Note: the stock stop can be used for multiple angle cuts in the same way as described for straight cuts. See Using the stock stop for repeated cuts.

Material	Speed

Structural steel shapes	165
Low carbon steel	160-165
Medium carbon steel	115
High carbon steel	90-100
Cr-moly steel	105-135
Ni-Cr-moly steel	90-115
Chromium steel	80-140
Cr-vanadium steel	105-115
Tool steel	40-80
Stainless steel	40-70
Free machining steel	80-100
Cast iron	55-90
Copper alloy (CU-Zm)	55
Bronze	90
Al-bronze	40
Monel	40-45
Titanium alloy	25-40
Aluminum (T-6+)	80-160

J-3410-2, J-3410 specifications

Jet Tools is renowned for its high-quality woodworking and metalworking equipment, and the J-3410 and J-3410-2 drill presses are prime examples of this commitment to excellence. These machines are engineered for precision, durability, and efficiency, appealing to both hobbyists and professional craftsmen.

The J-3410 features a robust 1 HP motor that provides ample power for a variety of drilling applications. This strength enables it to handle a wide range of materials, making it versatile enough for various projects. The machine operates at five different speeds, ranging from 600 to 3,100 RPM, allowing users to select the ideal speed for the specific material and drill bit size they are using. This versatility is crucial for achieving the desired results, whether it’s delicate woodwork or tougher metals.

One of the standout features of the J-3410 is its adjustable table, which can tilt up to 45 degrees, facilitating angled drilling. The table is constructed from heavy-duty cast iron, ensuring stability and reducing vibration, which is vital for precision work. Additionally, this model comes with a built-in laser guide that provides an accurate reference point for drilling, enhancing user efficiency and accuracy.

The J-3410-2 model builds upon the features of the J-3410, offering dual laser guides for even greater precision. These guides help users easily align the drill bit, ensuring that holes are drilled exactly where intended. The dual lasers also enhance visibility, especially in low-light environments. This model also includes a larger work table, allowing for drilling operations on bigger workpieces without compromising stability.

Both models are equipped with a heavy-duty, quick-adjust depth stop. This feature allows for consistency in repetitive drilling tasks, which is essential for users who need to achieve uniform results. They also feature an easy-to-use belt and pulley system for speed changes, ensuring that the transition between different speeds is effortless.

Safety is paramount in the design of the J-3410 and J-3410-2 press. A protective on/off switch prevents accidental start-ups, while the cast iron construction enhances overall stability and reduces the likelihood of accidents during operation.

The Jet Tools J-3410 and J-3410-2 combine power, precision, and safety, making them excellent choices for anyone in need of reliable drilling equipment. Whether for professional use or personal projects, these drill presses stand out in their class, showcasing Jet's commitment to quality and innovation.

Jet Tools J-3410-2 Right angle cuts -- single pieces of stock, Angle cutting

Models: J-3410-2 J-3410