JL Audio SB-POL-RNGR/SYS manual N G R a T U L a T I O N S, E P 1, C L U D E D H a R D W a R E

Models: SB-POL-RNGR/SYS

1 3
Download 3 pages 16.46 Kb
Page 3
Image 3

S T E P 9

Install a piece of the included Self Adhesive Gasket Material along the outer edge of each frame rail where the OEM kick panels had been attached.

S T E P 1 0

Run the wire from each of the kick panels to the amplifier location, slide the kick panels into place using the opposite method from what was done to remove the OEM kick pan- els. Position the housings so that the screw holes along the frame rail line up with the holes in the enclosure. Using the OEM hardware, attach each enclosure to the frame rails of the vehicle.

S T E P 1 1

Along the inner edge of each speaker housing there are two screw holes that will need to have pilot holes drilled and then have the supplied 1/4x 1” Button Head Allen Bolts installed through the flanges and the floor, under the floor there should be a fender washer against the floor and, a 1/4-20 Locknut installed to secure the speaker housings to the floor of the vehicle.

S T E P 1 2

C O N G R A T U L A T I O N S !

You have completed the installation for this model!

Enjoy your new Stealthbox®! Go out in the woods and get dirty!

Please refer to the Power Recommendation section for an amplifier recommendation and basic set-up help.

 

 

 

SB-POL-RNGR/SYS INSTR_SKU# 011278

I N C L U D E D H A R D W A R E

 

 

 

1) Custom Aluminum Bracket

1) 3/8-16x 1 1/2” Hex Head Bolt

1)

3/8-16x 1” Hex Head Bolt

1)

3/8 x 1 1/4” Fender Washer

4)

3/8 Split Locking Washer

1)

3/8 Flat Washer

1)

Square U-Bolt (with washers and, nuts)

4) 1/4x 1” Button Head Allen Bolt

4)

1/4-20 Lock Nut

1)

1/2x 1” Custom Aluminum Spacer

S P E C I F I C A T I O N S

Subwoofer Enclosure Type: Acoustic Suspension (sealed)

Driver Type: M10W5

Nominal Impedance: 4 Ohms

Continuous Power Handling: 250 Watts (RMS)

Kickpanel Enclosure Type: Infinite Baffle

Driver Type: M770-CCX

Nominal Impedance: 4 Ohms

Continuous Power Handling: 100 Watts (RMS)

P o w e r R e c o m m e n d a t i o n

JL Audio recommends using a high quality amplifier such as the JL Audio M4500. The diagram below shows the recommended crossover and input settings for the M4500 when being used to power your Stealthbox®.

The JL Audio M4500 is a very versatile audio component. Please consult the owner’s manual for even more detailed information about installing and tuning this amplifier.

(954) 443-1100

 

www.jlaudio.com

 

 

 

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered

 

 

 

 

trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.

 

 

 

 

JLA-SKU#011278 ©10-15-2008 • Printed in USA • ©2008 JL Audio, Inc. • U.S. PATENTS:

#5,734,734 #5,949,898 #6,118,884 #6,229,902

 

 

 

 

#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign

 

 

 

 

patents pending. For more detailed information please visit us online at www.jlaudio.com.

 

 

 

 

 

 

1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y

M I R A M A R , F L O R I D A

3 3 0 2 5

U S A

Page 3 • JL Audio, Inc 2008

Page 3
Image 3
JL Audio SB-POL-RNGR/SYS manual N G R a T U L a T I O N S, E P 1, C L U D E D H a R D W a R E, Specification S