TDK 750W, 1500W technical manual Chapter, Specifications

		CHAPTER 2	SPECIFICATIONS
2.1 OUTPUT RATING
MODEL				GEN	6-100	8-90	12.5-60	20-38	30-25	40-19		–	60-12.5	80-9.5	100-7.5	150-5		300-2.5	600-1.3
1.Rated output voltage (*1)				V	6	8	12.5	20	30	40		–	60	80	100		150	300	600
2.Rated output current 750W (*2)				A	100	90	60	38	25	19		–	12.5	9.5	7.5		5	2.5	1.3
3.Rated output power 750W				W	600	720	750	760	750	760		–	750	760	750		750	750	780
MODEL				GEN	6-200	8-180	12.5-120	20-76	30-50	40-38		50-30	60-25	80-19	100-15	150-10		300-5	600-2.6
1.Rated output voltage (*1)				V	6	8	12.5	20	30	40		50	60	80	100		150	300	600
2.Rated Output Current 1500W (*2)				A	200	180	120	76	50	38		30	25	19	15		10	5	2.6
3.Rated output power 1500W				W	1200	1440	1500	1520	1500	1520		1500	1500	1520	1500		1500	1500	1560
2.2 INPUT CHARACTERISTICS
				V	6	8	12.5	20	30	40		50	60	80	100		150	300	600
1.	Input voltage/freq. (*3)			–	85~265Vac continuous, 47-63Hz, single phase.
2.	Input current (at 100/200Vac)			A	10.5/5 for 750W model, 21/11 for 1500W models.
3.	Power Factor			–	0.99@100/200Vac, rated output power.
4.	750W models Efficiency (*4)			%	76/78	77/80	81/84	82/85	82/85	83/87		83/87	83/87	83/87	83/87		83/87	83/87	83/87
5.	1500W models Efficiency (*4)			%	77/79	78/81	82/85	83/86	83/86	84/88		84/88	84/88	84/88	84/88		84/88	84/88	84/88
6.	Inrush current at 100/200V			A	Less than 25A for 750W models, 50A for 1500W models.
2.3 CONSTANT VOLTAGE MODE
				V	6	8	12.5	20	30	40		50	60	80	100		150	300	600
1.	Max.Line regulation (*5)			–	0.01% of rated output voltage +2mV
2.	Max.Load regulation (*6)			–	0.01% of rated output voltage +2mV
3. Ripple and noise (p-p,20MHz) (*10)				mV	60	60	60	60	60	60		60	60	80	80		100	150	300
4. Ripple r.m.s., 5Hz~1MHz (*10)				mV	8	8	8	8	8	8		8	8	8	8		10	25	60
5.	Temperature coefficient			PPM/°C	100PPM/°C of rated output voltage, following 30 minutes warm up
6.	Temperature drift			–	0.05% of rated Vout over 8hrs interval following 30 minutes warm-up. Constant line, load & temp.
7. Rem. Sense compensation/wire				V	1	1	1	1	1.5	2		2	3	4	5		5	5	5
8. Up-prog. Response time 0~Vomax (*9)				mS				80							150				250
9. Down-prog. Response time: Full load				mS	10		50				80				150				250
			No load		500	600	700	800	900	1000		1100	1100	1200	1500		2000	2500	4000
10. Transient response time				mS	Time for the output voltage to recover within 0.5% of its rated output for a load change 10~90% of rated
					output current.
					Output set-point: 10~100%.
					Less than 1mS for models up to and including 100V; 2mS for models above 100V.
11. Hold-up time				mS	More than 20mS, 100Vac, rated output power.
2.4 CONSTANT CURRENT MODE
				V	6	8	12.5	20	30	40		50	60	80	100		150	300	600
1.	Max.line regulation (*5)			–	0.01% of rated output voltage +2mA
2.	Max.load regulation (*7)			–	0.02% of rated output current +5mA
3. Ripple r.m.s. 5Hz~1MHz.750W (*8)				mA	200	180	120	76	63	48		–	38	29	23		18	13	8
		1500W (*8)		mA	400	360	240	152	125	95		75	75	57	45		35	25	12
4.	Temperature coefficient			PPM/°C	100PPM/°C from rated output current, following 30 minutes warm-up.
5.	Temperature drift			–	0.05% of rated lout over 8hrs interval following 30 minutes warm-up. Constant line, load & temp.
2.5 ANALOG PROGRAMMING AND MONITORING
1.Vout voltage programming				–	0~100%, 0~5V or 0~10V, user select. Accuracy and linearity; +/-0.5% of rated Vout.
2.	Iout voltage programming			–	0~100%, 0~5V or 0~10V, user select. Accuracy and linearity; +/-1% of rated Iout.
3.	Vout resistor progrmming			–	0~100%, 0~5/10Kohm full scale, user select. Accuracy and linearity: +/-1% of rated Vout.
4.	Iout resistor programming			–	0~100%, 0~5/10Kohm full scale, user select. Accuracy and linearity: +/-1.5% of rated Iout.
5.	On/off control			–	By electrical Voltage: 0~0.6V/2~15V or dry contact, user selectable logic.
6.	Output current monitor			–	0~5V or 0~10V, user selectable. Accuracy: 1%
7.	Output voltage monitor			–	0~5V or 0~10V, user selectable. Accuracy: 1%
8.	Power supply OK signal			–	4~5V-OK, 0V-Fail, 500ohm series resistance.
9.	Parallel operation			–	Possible, up to 4 units in master/slave mode with single wire current balance connection.
10. Series operation				–	Possible (with external diodes), up to 2 units.
11. CV/CC inicator				–	CV: TTL high (4~5V), source current: 10mA, CC: TTL low (0-0.6V). Sink current: 10mA .
12. Enable/Disable				–	Dry contact. Open: off, Short: on. Max. voltage at Enable/Disable in: 6V.
13. Local/Remote analog control				–	By electrical signal or Open/Short: 0~0.6V or short: Remote, 4~5V or open: Local.
14. Local/remote analog indicator				–	Open collector. Local: Open, Remote: On. Maximum voltage: 30V, maximum sink current: 5mA.

9

83-507-013 Rev. D